80 Watt Full Cutoff LED Wall Pack | 10300 Lumens | 5000K | 100-277V

Product Overview

This 80 Watt Full Cutoff LED Wall Pack is designed for exterior wall mounting on commercial and industrial buildings. It delivers 10,300 lumens at 5000K, providing high-output illumination for perimeter and security lighting. The fixture is built for direct replacement of 250W metal halide wall packs, offering improved efficiency and reduced maintenance.

The full cutoff design minimizes uplight and glare, supporting compliance with dark sky requirements in many jurisdictions. Typical mounting heights range from 8 to 15 feet on building exteriors, including warehouses, service areas, and multifamily properties.

Core Performance and Output

This wall pack outputs 10,300 lumens at 80 watts, achieving 129 lumens per watt. The 5000K color temperature provides a neutral white light suitable for security and exterior visibility. The polycarbonate lens delivers a uniform forward throw distribution, supporting perimeter coverage and entry illumination.

Performance is optimized for wall heights up to 15 feet. At lower mounting heights, output may be excessive for pedestrian-only areas. Uniformity can decrease if fixtures are spaced too far apart on long building facades.

Adjustability and Control Options

This fixture operates on 100-277V input and is compatible with standard wall-mounted electrical circuits. It does not include integrated motion or daylight sensors, but can be controlled via external switching or building automation systems.

The full cutoff housing is fixed in orientation and does not provide adjustable aiming. Dimming is not included as standard. For applications requiring adaptive control, external controls must be specified separately.

Longevity and Reliability

The LED system is rated for 50,000 hours (L70), supporting multi-year operation with minimal lumen depreciation. The die-cast aluminum housing and polycarbonate lens are designed for outdoor durability and impact resistance.

Operating temperature range is -40°F to 113°F. The fixture is IP65 rated for protection against dust and water jets, suitable for exposed exterior installations. Routine cleaning of the lens and housing is recommended to maintain output and appearance.

Build Quality and Physical Characteristics

The fixture measures 11.7 inches long, 3.6 inches wide, and 8.6 inches deep. The housing is bronze-finished die-cast aluminum with a sealed polycarbonate lens. All hardware is corrosion-resistant for long-term exterior use.

Wall mounting is supported via integral backplate. The fixture is designed for direct surface mounting to masonry, concrete, or structural exterior walls. The compact form factor allows installation in areas with limited wall space or architectural constraints.

Where This Product Fits Best

This wall pack is suited for exterior wall lighting on commercial, industrial, and multifamily buildings. It is commonly used to provide security, perimeter, and entry illumination where full cutoff performance is required.

• security lighting
• building facade lighting
• building exterior lighting
• commercial exterior wall lighting
• perimeter lighting
• entry lighting
• service area lighting
• multifamily exterior lighting

Environments include warehouses, service corridors, loading areas, and apartment building exteriors. The IP65 rating supports use in wet or exposed locations. Not intended for canopy, ceiling, or pole mounting.

Installation and Long-Term Use

Installation is direct to exterior walls using the integrated backplate. The fixture accepts 100-277V input and is compatible with standard building wiring. All connections are made within the sealed housing to maintain IP65 protection.

Long-term maintenance is limited to periodic cleaning and inspection. The LED system is non-serviceable; replacement is required at end of life. The fixture is designed for minimal maintenance in demanding exterior environments.

How This Fixture Is Commonly Used

Typical mounting heights are 8 to 15 feet, spaced 15 to 30 feet apart depending on required light levels and site geometry. Fixtures are installed in continuous runs along building facades or at targeted locations such as entries and service doors.

Higher output allows for wider spacing, but may increase glare if installed at low heights or near pedestrian pathways. Layouts should consider site security requirements and local lighting codes.

Safety, Certifications, and Warranty

This fixture is ETL certified and IP65 rated. It is suitable for wet locations and meets requirements for exterior wall lighting in commercial and industrial settings. The product is rebate eligible where local programs apply.

A 5-year warranty covers manufacturing defects and LED performance. All components are rated for outdoor use and long-term reliability.

Frequently Asked Questions

Q: What is the recommended mounting height for this wall pack?

A: Recommended mounting height is 8 to 15 feet for optimal coverage and uniformity.

Q: Can this fixture be installed on any exterior wall material?

A: The fixture can be mounted to masonry, concrete, or structural exterior walls using the included backplate.

Q: Is this wall pack suitable for use in wet or exposed outdoor locations?

A: Yes, the fixture is IP65 rated for wet locations and direct exposure to weather.

Q: Does this fixture support dimming or motion sensing?

A: Dimming and motion sensing are not integrated; external controls must be specified separately if required.

Q: How many fixtures are needed for continuous coverage along a building facade?

A: Spacing typically ranges from 15 to 30 feet depending on mounting height and required light levels.

Application Questions and Clarification

Q: Is this wall pack appropriate for entry lighting on multifamily buildings?

A: Yes, it is commonly used for entry and perimeter lighting on multifamily exteriors.

Q: Can this fixture be used for loading area lighting?

A: The output and distribution are suitable for loading area wall lighting when mounted at appropriate heights.

Q: Is this product intended for pole or canopy mounting?

A: No, this fixture is designed for direct wall mounting only.

Q: Does the full cutoff design help with dark sky compliance?

A: The full cutoff housing minimizes uplight and supports dark sky requirements in many locations.