100 Watt Full Cutoff LED Wall Pack | 12900 Lumens | 5000K | 100-277V

Product Overview

We offer the 100 Watt Full Cutoff LED Wall Pack for exterior wall-mounted lighting applications requiring moderate to high output. This fixture is designed for perimeter illumination, security, and building facade lighting where cutoff optics are needed to control light spill and glare. Typical installations include mounting heights from 8 to 15 feet on commercial and industrial building exteriors, replacing legacy 250W metal halide wall packs.

The fixture operates at 100-277V and delivers 12900 lumens at 5000K. The full cutoff design provides forward-throw distribution while minimizing uplight, supporting compliance with dark sky and site lighting requirements.

Core Performance and Output

This wall pack produces 12900 lumens at 100 watts, achieving an efficacy of 129 lumens per watt. The 5000K color temperature supports high-visibility exterior environments. The polycarbonate lens and full cutoff housing direct light outward and downward, reducing glare and light trespass.

Output is suitable for medium to large building perimeters, service areas, and loading zones. At mounting heights below 8 feet, output may be excessive and increase glare. Uniformity may decrease if spacing exceeds recommended distances for the wattage and distribution pattern.

Adjustability and Control Options

This fixture provides fixed forward-throw distribution with a full cutoff profile. There are no integrated motion sensors or dimming controls included as standard. The fixture is compatible with external control systems that operate on switched or time-based circuits within the 100-277V range.

Optical adjustment is not available. The fixture is designed for applications where consistent, directional illumination is required without field aiming or beam shaping.

Longevity and Reliability

The LED system is rated for 50,000 hours (L70), supporting multi-year operation with minimal maintenance. The driver and LEDs are thermally managed within a die-cast aluminum housing to maintain performance in outdoor environments.

Operating temperature range is -40°F to 113°F. The fixture is suitable for year-round exterior use in most climates. Polycarbonate lens resists impact and UV degradation over time.

Build Quality and Physical Characteristics

The housing is constructed from die-cast aluminum with a bronze finish. The fixture measures 11.7 inches long, 3.6 inches wide, and 8.6 inches deep. The polycarbonate lens is sealed to the housing for weather resistance.

IP65 rating protects against dust and water ingress. All hardware and gasketing are designed for exterior wall mounting. The fixture color and form factor match common commercial and industrial building aesthetics.

Where This Product Fits Best

This wall pack is intended for exterior wall mounting on commercial, industrial, and multifamily buildings. It is used where forward-throw, cutoff distribution is needed for safety, security, and site illumination. The fixture is appropriate for new construction or retrofit projects replacing metal halide wall packs.

• security lighting
• building facade lighting
• building exterior lighting
• commercial exterior wall lighting
• perimeter lighting
• entry lighting
• service area lighting
• loading area lighting

Suitable for outdoor environments exposed to rain, dust, and temperature fluctuations. Not intended for interior use or locations requiring uplight or decorative accent lighting.

Installation and Long-Term Use

The fixture mounts directly to exterior walls using standard hardware. Electrical connection is made to 100-277V circuits. The compact form factor allows installation on masonry, concrete, or metal surfaces.

Routine maintenance is limited to periodic cleaning of the lens and inspection of seals. No lamp or ballast replacements are required. The fixture is designed for long-term operation with minimal service intervention.

How This Fixture Is Commonly Used

Typical mounting heights range from 8 to 15 feet, depending on the area to be illuminated and required light levels. Fixtures are spaced to provide overlapping coverage along building perimeters, entries, and service areas.

Layout patterns vary based on wall length and site geometry. Higher output allows for wider spacing but may increase glare if installed too low or too close to pedestrian areas. Full cutoff optics help control light spill onto adjacent properties.

Safety, Certifications, and Warranty

This fixture is ETL listed and IP65 rated. It meets requirements for exterior wet location use. Power factor is greater than 0.90 and total harmonic distortion is less than 20%.

The product includes a 5-year warranty covering manufacturing defects and LED performance. All components are rated for outdoor commercial and industrial environments.

Frequently Asked Questions

Q: What is the recommended mounting height for this 100W wall pack?

A: Recommended mounting height is 8 to 15 feet for optimal coverage and uniformity.

Q: Can this fixture be used to replace a 250W metal halide wall pack?

A: Yes, this fixture is designed to replace 250W metal halide wall packs in exterior applications.

Q: Is the fixture compatible with photocells or motion sensors?

A: The fixture does not include integrated controls but can be used with external photocells or sensors on the circuit.

Q: What is the spacing guideline for perimeter lighting with this wall pack?

A: Spacing typically ranges from 20 to 30 feet, depending on mounting height and required light levels.

Q: Does the fixture support dimming?

A: This model does not include dimming capability as standard.

Application Questions and Clarification

Q: Is this wall pack suitable for use in loading area lighting?

A: Yes, the output and distribution are appropriate for loading area lighting on building exteriors.

Q: Can this fixture be installed for multifamily exterior lighting?

A: The fixture is suitable for multifamily exterior wall lighting where full cutoff and moderate to high output are required.

Q: Is this product appropriate for entry lighting on commercial buildings?

A: Yes, it is commonly used for entry lighting on commercial and industrial building exteriors.

Q: Does the IP65 rating cover exposure to rain and dust?

A: The IP65 rating provides protection against rain and dust for outdoor wall-mounted installations.