LED Full Cutoff Wall Packs - Dark Sky Compliant

What are Full Cutoff LED Wall Packs?

LED full cutoff wall pack lights direct all illumination downward, eliminating upward light spill that causes glare and sky glow. Unlike traditional wall packs that scatter light, these fixtures use precision optics to focus every lumen on the intended area. Full cutoff design meets Dark Sky compliance requirements when properly specified, maximizing visibility and safety for walkways, parking areas, and building perimeters. The controlled distribution reduces light trespass onto neighboring properties and creates uniform illumination patterns for enhanced security.

Selecting the Best Full Cutoff LED Wall Packs

Brightness needs drive selection, with most commercial applications requiring 2,000 to 8,000 lumens, depending on mounting height and coverage. We typically recommend 20-30 watts for standard entrances and 40-80 watts for larger perimeters. Die-cast aluminum housing with polycarbonate lenses offers durability for years of outdoor use when maintained.

Consider selectable wattage models to fine-tune light levels after installation, depending on the model. 120-277V drivers adapt to your building's electrical system, simplifying planning. Motion sensor compatibility adds security and reduces energy use during low-traffic periods.

Beam angle matters - Type III distribution is best for general area lighting, while Type V distribution suits corner mounting.

Case Study: Outdoor Wall Pack Perimeter Security Lighting in Hartwell, GA

After: 12 / 18 / 24 / 30 Watt Adjustable Full Cutoff Architectural LED Wall Pack	After: 12 / 18 / 24 / 30 Watt Adjustable Full Cutoff Architectural LED Wall Pack

Lighting Plan We Created for the Customer

Lighting Plan	Heat Map

Outdoor Wall Pack Security Lighting Installation Plan Metrics

• Mounting height: 9 ft
• Fixture Used: LLS-WD-AWPFC-12/18/24/30-CC-PC: 12 / 18 / 24 / 30 Watt Adjustable Full Cutoff Architectural LED Wall Pack | 1584 to 3960 Lumens | 3000K / 4000K / 5000K Adjustable | 100-277V | Built-In Photocell
• FC achieved: 1.11 average
• Uniformity (Avg/Min): N/A

Advantages of LED Full Cutoff Wall Packs

LEDs use much less energy than HID technology. A 40-watt LED wall pack can replace a 150-watt metal halide fixture while providing better light quality and distribution. This results in 60-70% lower electricity costs and reduced HVAC load from less heat output.

• Long Operating Life: Over 50,000 hours with L70 rated performance per manufacturer specifications, reducing maintenance labor
• Instant-On Performance: Full brightness immediately, unlike HID fixtures that require warm-up
• Weatherproof Construction: IP65 weatherproof rating withstands rain, snow, and temperature extremes from -40F to 104F
• Optical Precision: Precise control prevents light pollution and maximizes ground-level illumination uniformity
• Rebate Eligibility: DLC Premium certification qualifies for maximum utility rebates and energy incentives

Controlling the Brightness of LED Wall Packs

Most commercial wall packs include 0-10V dimming capability for integration with building automation and occupancy sensors, depending on the model. Dimming extends fixture life and provides adaptive lighting based on usage.

Motion sensor integration allows fixtures to operate at 20-30% output during vacant periods, then ramp to full brightness when activity is detected. This approach maintains security visibility while maximizing energy savings.

How to Install LED Wall Packs

Mount fixtures to solid masonry or structural elements using the provided bracket and appropriate fasteners. Most installations require a 4-inch round or octagonal junction box recessed into the wall. Route supply wiring through the back entry, connecting line voltage to the driver. Universal input drivers accept 120V through 277V without extra configuration. Professional installation ensures proper weathersealing and code compliance as verified by the local authority.

Features to Consider When Buying LED Full Cutoff Wall Packs

Color temperature affects atmosphere and visibility. 3000K warm white creates welcoming light for entrances and hospitality, while 5000K daylight provides crisp visibility for security cameras and matches metal halide installations.

Wattage selection depends on mounting height and coverage. Standard 8-foot mounting heights work with 20-40 watt fixtures, while 12-foot installations benefit from 60-80 watt models. Photocell integration enables automatic dusk-to-dawn operation.

Emergency battery backup options keep critical lighting operational during power outages, meeting egress lighting requirements when properly specified.

What are the Cost Savings and ROI When You Convert from Metal Halide to LED?

60W LED Wall Packs vs 250W Metal Halide Replacement (with ballast)

Assumptions: Based on 12 hours/day, 365 days/year at $0.15/kWh, 20 fixture(s), and a 15% ballast factor applied to the metal halide wattage (250W lamp + 15% ballast = ~ 288W input).
•  Energy cost and ROI calculations are based on energy savings only and assume an LED fixture cost of $100.00 per fixture.
• Maintenance savings from reduced bulb and ballast replacements are not included in these calculations.

In this example with 20 fixture(s), total LED fixture investment is approximately $2,000.00, and estimated annual energy-only savings are $2,989.35. Simple payback based on energy savings alone is under 9 months. Maintenance savings from eliminating metal halide bulb and ballast replacements provide additional value throughout the fixture's 50,000-hour lifespan, but are not included in this ROI calculation.

Safety and Performance Certifications

All our fixtures carry essential certifications, including DLC Premium for energy efficiency and rebate eligibility, UL Listed for electrical safety, and ETL Listed for product safety compliance. These certifications help ensure safety, performance, and energy efficiency, and may qualify your project for utility rebates and tax incentives. DLC Premium certification verifies high efficiency standards and rebate eligibility.

5-Year Warranty and Support

All our lights come with at least a 5-year warranty, and warranty support is based in the USA. Our experienced support team understands the importance of keeping your lighting operational and will work quickly to resolve any warranty issues.

Expert Guidance for Your Wall Pack Project

LED Lighting Supply's product specialists bring 15+ years of commercial lighting experience to help you avoid costly mistakes. Our team analyzes your site-specific requirements, including mounting heights, spacing, and Dark Sky compliance, to recommend the optimal wall pack configuration.

We create custom lighting plans showing fixture placement and photometric data, ensuring uniform coverage and eliminating dark spots. Our energy savings calculations factor in your local utility rates and operating schedules to provide accurate ROI projections. This expert consultation helps ensure your wall pack selection delivers the performance and savings you need.

LED Full Cutoff Wall Packs - Dark Sky Compliant Frequently Asked Questions

What are Full Cutoff LED Wall Packs?

Full cutoff LED wall packs direct all illumination downward to eliminate upward light spill, meeting Dark Sky compliance requirements when properly specified. The controlled light distribution reduces light trespass onto neighboring properties while creating uniform illumination patterns for walkways, parking areas, and building perimeters.

How do I select the right Full Cutoff LED Wall Pack?

Most commercial applications need between 2,000 to 8,000 lumens, with 20-30 watts for standard building entrances and 40-80 watts for larger parking lot perimeters. Type III distribution works for general area lighting, while Type V distribution suits corner mounting applications.

What are the advantages of LED Full Cutoff Wall Packs?

A 40-watt LED wall pack replaces a 150-watt metal halide fixture, delivering 60-70% lower electricity costs. Operating life exceeds 50,000 hours at L70 rated performance, and DLC Premium certification qualifies installations for maximum utility rebates.

How do I control the brightness of LED Wall Packs?

Most commercial-grade wall packs include 0-10V dimming capability that integrates with building automation systems and occupancy sensors, depending on the model. Motion sensor integration allows fixtures to operate at 20-30% output during vacant periods, then ramp to full brightness when activity is detected.

How do I install LED Wall Packs?

Most installations require a 4-inch round or octagonal junction box recessed into the wall surface, with universal input drivers accepting 120V through 277V without additional configuration. Professional installation ensures proper weathersealing and that electrical connections meet local code requirements as verified by the local government authority.

What features should I consider when buying Full Cutoff LED Wall Packs?

3000K warm white creates welcoming illumination for building entrances, while 5000K daylight enhances security camera performance. Standard 8-foot mounting heights work with 20-40 watt fixtures, while 12-foot installations benefit from 60-80 watt models, subject to site conditions.

What safety and performance certifications should I look for?

Fixtures carry DLC Premium, UL Listed, and ETL Listed approvals, ensuring safety and performance while qualifying for utility rebates. IP65 weatherproof rating withstands rain, snow, and temperature extremes from -40F to 104F.

What warranty coverage is included?

All lights include at least a 5-year warranty with USA-based support.