45 Watt Detention Grade Surface Mount 1x4 LED Panel | 7000 Lumens | 4000K | 100-277V

Product Overview

This 45 Watt Detention Grade Surface Mount 1x4 LED Panel is designed for secure environments requiring high durability and tamper resistance. The fixture delivers 7000 lumens at 4000K, providing uniform illumination suitable for correctional and detention facilities. Surface mounting and tamper-resistant fasteners support secure installation in areas where vandalism or abuse is a concern.

The fixture is built for use in correctional cells, secure corridors, and other high-risk locations where standard commercial lighting is not suitable. Typical mounting heights range from 8 to 12 feet, matching common ceiling heights in secure facilities.

Core Performance and Output

This fixture outputs 7000 lumens at 45 watts, achieving an efficacy of 156 lumens per watt. The 4000K color temperature provides neutral white light, supporting visibility and safety in secure environments. The optical system uses a .125 prismatic acrylic inner lens and a .156 clear polycarbonate outer lens for controlled light distribution and impact resistance.

0-10V dimming is standard, allowing integration with compatible control systems. At mounting heights below 8 feet, output may be excessive for small holding cells or confined spaces. Uniformity is maintained across typical corridor and cell layouts, but wide open areas may require additional fixtures for consistent coverage.

Adjustability and Control Options

The fixture supports 0-10V dimming for basic light level adjustment. This allows facility operators to reduce output during low-activity periods or for energy management. No onboard sensor or advanced control options are included; external controls must be specified separately if required.

Optical distribution is fixed by the dual-layer lens system. There are no field-adjustable beam options. The fixture is designed for consistent, diffuse illumination in secure spaces.

Longevity and Reliability

Rated for 100,000 hours (L70), this fixture is intended for long-term operation with minimal maintenance. The LED driver and light engine are selected for continuous use in institutional environments. The 16-gauge steel housing and polycarbonate lens system resist impact and tampering, reducing the risk of damage or premature failure.

All components are specified for 50/60 Hz operation at 100-277V, supporting compatibility with standard facility electrical systems. The fixture is suitable for continuous operation in secure areas where access for maintenance is limited.

Build Quality and Physical Characteristics

The housing is fabricated from 16-gauge cold rolled steel, finished in white. Tamper-resistant T25 TORX screws secure the lens and housing, deterring unauthorized access. The lens assembly combines a prismatic acrylic inner layer with a clear polycarbonate outer shield for impact resistance and light diffusion.

The fixture measures 47.75 inches by 12.19 inches by 4 inches, supporting installation in standard 1x4 ceiling openings or surface-mount applications. IK07 impact rating and ETL certification are standard. All hardware is designed for institutional use in high-abuse environments.

Where This Product Fits Best

This fixture is intended for secure environments where vandal resistance and tamper-proof construction are required. Typical installations include:

• detention facility lighting
• correctional facility lighting
• secure area lighting
• vandal resistant lighting
• psychiatric facility lighting
• holding cell lighting
• secure corridor lighting
• tamper resistant lighting

The fixture is suitable for indoor use in areas with high risk of abuse or tampering. It is not intended for wet locations or exterior use. The design supports installation in institutional settings with standard ceiling heights and secure mounting requirements.

Installation and Long-Term Use

Surface mounting is standard, with tamper-resistant fasteners included. The fixture is designed for direct attachment to solid ceilings or secure mounting surfaces. All wiring and access points are protected by the steel housing and lens system.

Routine maintenance is minimized by the long LED lifespan and robust construction. Access for relamping or driver replacement is restricted by tamper-resistant hardware, supporting security protocols. Installation should be performed by qualified personnel familiar with secure facility requirements.

How This Fixture Is Commonly Used

Typical mounting heights range from 8 to 12 feet, matching secure corridor and cell ceiling heights. Fixtures are spaced to provide uniform illumination, often in continuous rows or at regular intervals along corridors. In holding cells, one fixture per room is common.

Spacing and layout depend on required light levels and room geometry. Higher output can reduce fixture count but may increase glare in confined spaces. Layouts should be coordinated with facility security and maintenance protocols.

Safety, Certifications, and Warranty

This fixture is ETL listed and IK07 impact rated. All hardware is tamper-resistant. The lens system is designed for impact resistance and secure installation. The product is covered by a 5-year warranty.

All certifications and ratings are documented for compliance with institutional and correctional facility standards. The fixture is rebate eligible where applicable.

Frequently Asked Questions

Q: What is the recommended mounting height for this fixture?

A: Typical mounting heights are 8 to 12 feet, matching secure corridor and cell ceilings.

Q: Can this fixture be installed in wet or exterior locations?

A: No, this fixture is intended for indoor use only and is not rated for wet or exterior environments.

Q: What type of fasteners are used for installation?

A: Tamper-resistant T25 TORX screws are used to secure the housing and lens assembly.

Q: Is the fixture compatible with lighting controls?

A: 0-10V dimming is standard. Additional controls require external devices and are not integrated.

Q: How should fixtures be spaced for uniform lighting in corridors?

A: Spacing depends on corridor width and required light levels. Uniformity is typically achieved with fixtures spaced 8 to 12 feet apart.

Application Questions and Clarification

Q: Is this fixture suitable for psychiatric facility patient rooms?

A: Yes, the tamper-resistant design and impact-rated lens system are appropriate for psychiatric facility lighting applications.

Q: Can this fixture be used in secure corridors with high abuse risk?

A: Yes, the fixture is designed for secure corridor lighting and environments with high risk of vandalism or tampering.

Q: Is this fixture appropriate for holding cell lighting?

A: Yes, it is commonly installed in holding cells where secure, vandal-resistant lighting is required.

Q: Does the fixture support tamper resistant lighting requirements?

A: Yes, all hardware and lens assemblies are tamper-resistant and meet requirements for tamper resistant lighting.