100 Watt Hybrid Solar Area Light | 20000 Lumens | 4000K | 120-277V | High Performance | 5 Year Warranty

Product Overview

The 100 Watt Hybrid Solar Area Light is designed for exterior site lighting where grid power is available but energy savings and off-grid operation are priorities. This fixture integrates a monocrystalline solar panel with a high-efficiency LED array, supporting both solar and AC operation. Typical use cases include parking lots, municipal streets, and remote pathways where reliable illumination is required and trenching for power is impractical or cost-prohibitive.

This model delivers 20,000 lumens at 4000K, providing a neutral white light suitable for visibility and safety in outdoor environments. The slip fitter mount supports installation on standard poles, and the fixture is sized for medium to large area coverage. The integrated motion sensor enables adaptive lighting control to further reduce energy use.

Core Performance and Output

This fixture outputs 20,000 lumens at 100 watts, achieving 200 lumens per watt. The Type 3 beam distribution is designed for roadway and area lighting, providing wide lateral coverage suitable for streets and parking lots. The 4000K color temperature supports visual clarity without excessive glare.

Performance is consistent across the 100-277V input range, with solar operation supplementing or replacing grid power as available. Output may be excessive for small pathways or low mounting heights below 15 feet. At mounting heights above 30 feet, uniformity may decrease and additional fixtures may be required for continuous coverage.

Adjustability and Control Options

The fixture includes an integrated motion sensor for occupancy-based dimming or on/off control. This supports adaptive lighting strategies, reducing energy use during periods of low activity. The slip fitter mount allows for horizontal and vertical adjustment to optimize aiming and coverage.

No onboard dimming is provided beyond the motion sensor function. Control integration is limited to the built-in sensor; external control systems are not supported. The solar panel is fixed and sized for the fixture?s output and battery capacity.

Longevity and Reliability

The LED array is rated for 100,000 hours (L70), supporting long-term operation with minimal maintenance. The monocrystalline solar panel is designed for extended outdoor exposure and consistent energy harvesting over its service life.

All components are housed in an IP65-rated enclosure, providing protection against dust and water ingress. The fixture is suitable for year-round exterior use in most climates. Battery life and solar performance may vary with geographic location and seasonal sunlight availability.

Build Quality and Physical Characteristics

The housing is constructed from aluminum alloy for corrosion resistance and durability. The integrated solar panel is monocrystalline for high conversion efficiency. Polycarbonate optics provide impact resistance and stable light distribution.

The fixture measures 60 x 16.6 x 10 inches and weighs 53 lbs. The slip fitter mount is compatible with standard round poles. The EPA rating of 1.8 should be considered when selecting poles for wind load compliance.

Where This Product Fits Best

This hybrid solar area light is intended for exterior environments where grid power is present but energy savings, resilience, or off-grid capability are required. It is commonly installed in municipal, commercial, and campus settings where trenching for new power lines is impractical or where sustainability goals are prioritized.

• street lighting
• parking lot lighting
• pathway lighting
• remote site lighting
• park lighting
• trail lighting
• campus lighting
• municipal lighting

IP65 construction supports use in wet and dusty environments. The fixture is suitable for pole heights from 15 to 30 feet. Solar performance is optimal in locations with direct sunlight exposure.

Installation and Long-Term Use

Installation is performed using the slip fitter mount on round poles. The fixture?s weight and EPA require secure pole selection and proper anchoring for wind load compliance. All wiring for AC operation is contained within the fixture; no external drivers are required.

Routine maintenance is limited to periodic cleaning of the solar panel and inspection of the motion sensor. Battery replacement may be required over the service life, depending on usage and environmental conditions. The fixture is designed for minimal intervention in typical municipal or commercial maintenance cycles.

How This Fixture Is Commonly Used

This fixture is typically mounted at heights between 15 and 30 feet, with spacing determined by required light levels and site geometry. In parking lots and along streets, fixtures are spaced to provide overlapping coverage and minimize dark spots. Pathway and trail installations may use wider spacing where lower light levels are acceptable.

Higher output allows for reduced fixture count in large areas, but may increase glare if installed at low mounting heights. Motion sensor operation is commonly used to reduce energy use during periods of low activity, with full output triggered by occupancy.

Safety, Certifications, and Warranty

This product is IP65 rated. The housing and optics are impact resistant. The fixture is suitable for wet locations and outdoor use. The 5-year warranty covers defects in materials and workmanship under normal operating conditions.

All components are designed for compliance with typical municipal and commercial lighting standards. No additional certifications are claimed beyond IP65.

Frequently Asked Questions

Q: What is the recommended mounting height for this fixture?

A: Typical mounting heights range from 15 to 30 feet, depending on the application and required light levels.

Q: Does the fixture require grid power to operate?

A: The fixture can operate on solar power alone or in hybrid mode with 100-277V AC input. Grid power is not required if sufficient sunlight is available.

Q: How is the motion sensor configured?

A: The integrated motion sensor provides occupancy-based control, automatically switching between full output and reduced output or off when no motion is detected.

Q: What is the expected maintenance for the solar panel and battery?

A: Periodic cleaning of the solar panel is recommended to maintain performance. Battery replacement may be required over the fixture?s service life, depending on usage and environmental conditions.

Q: How should fixtures be spaced for parking lot or street applications?

A: Spacing depends on mounting height, site geometry, and required light levels. Typical spacing is 2 to 3 times the mounting height for uniform coverage.

Application Questions and Clarification

Q: Is this fixture suitable for use in municipal street lighting projects?

A: Yes, this fixture is designed for street lighting and meets the requirements for municipal and public roadway applications.

Q: Can this light be used for pathway or trail lighting in parks?

A: Yes, the fixture is suitable for pathway, trail, and park lighting where solar or hybrid operation is desired.

Q: Is this product appropriate for off-grid remote site lighting?

A: Yes, the hybrid solar design supports off-grid operation in remote locations with adequate sunlight exposure.

Q: What environmental conditions can this fixture withstand?

A: The fixture is IP65 rated for wet and dusty environments and is constructed for year-round outdoor use.