30 / 45 / 63 Watt Adjustable LED Canopy Light | 4000 to 8500 Lumens | 4000K / 5000K Adjustable | 100-277V | Bronze or White Finish

Product Overview

This is an adjustable LED canopy light designed for exterior covered environments requiring reliable, uniform illumination. The fixture supports selectable wattages of 30, 45, or 63 watts and delivers 4000 to 8500 lumens, making it suitable for both retrofit and new construction projects. Typical installations include gas station canopies and parking garage ceilings where consistent light levels and robust construction are required.

Color temperature can be set to either 4000K or 5000K during installation. The fixture is available in bronze or white finish and supports both pendant and surface mounting. The compact 9.5-inch square form factor and low profile allow for easy integration into canopy structures with limited clearance.

Core Performance and Output

This canopy light offers three selectable output levels: 4000, 6000, or 8500 lumens, with an efficacy of 135 lumens per watt. The 140° beam angle provides wide, even coverage suitable for open canopy layouts and drive-through areas. The fixture operates on 100-277V input and maintains consistent performance across the full voltage range.

Output at the highest setting is appropriate for mounting heights up to approximately 15 feet. At lower mounting heights, the highest wattage setting may produce excessive brightness or glare. The fixture does not support dimming or advanced controls.

Adjustability and Control Options

Wattage and color temperature are field adjustable via onboard switches, allowing for on-site tuning to match required light levels and color appearance. This flexibility supports both energy management and visual comfort objectives across different canopy zones.

No integrated motion sensors or networked controls are included. The fixture is designed for fixed-output operation once settings are selected during installation.

Longevity and Reliability

The fixture is rated for 50,000 hours (L70) and uses a die-cast aluminum housing for thermal management and durability. The polycarbonate lens resists impact and environmental exposure. The IP65 rating protects against dust and water ingress, supporting reliable operation in outdoor covered environments.

Operating temperature range is -40°F to 113°F. The fixture is suitable for year-round use in most climates without additional protection or maintenance requirements beyond standard cleaning.

Build Quality and Physical Characteristics

The housing is constructed from die-cast aluminum with a powder-coated finish in either bronze or white. The fixture measures 9.5 inches square by 3.5 inches high and weighs 3.7 pounds. The lens is polycarbonate for impact resistance and uniform light distribution.

All hardware is corrosion resistant. The fixture is designed for pendant or surface mounting to canopy structures and includes all necessary mounting components.

Where This Product Fits Best

This canopy light is intended for exterior covered environments requiring uniform, medium-output illumination and robust construction. It is commonly installed in:

• gas station lighting
• fueling area lighting
• parking canopy lighting
• drive-through canopy lighting
• covered walkway lighting
• loading canopy lighting
• entry canopy lighting
• commercial overhang lighting

The fixture is suitable for wet locations and environments exposed to vehicle exhaust, dust, and occasional water spray. It is not intended for open parking lots or high-bay interior spaces.

Installation and Long-Term Use

The fixture supports both pendant and surface mounting. Surface mounting is typical for concrete or metal canopy decks, while pendant mounting is used where conduit drops are required. The compact size allows for installation in tight or retrofit conditions.

Routine maintenance is limited to lens cleaning and periodic inspection of mounting hardware. The fixture is designed for minimal service requirements over its rated life. No special tools or proprietary accessories are needed for installation or adjustment.

How This Fixture Is Commonly Used

Typical mounting heights range from 8 to 15 feet, depending on the canopy structure and required light levels. Fixtures are spaced to provide uniform coverage, with spacing determined by output setting and canopy layout. For gas station canopies, fixtures are often installed in a grid pattern above fueling positions.

Higher output settings reduce the number of fixtures needed but may increase glare if installed at low heights. Adjusting wattage and color temperature during installation allows for tuning to site-specific requirements.

Safety, Certifications, and Warranty

This fixture is UL listed and IP65 rated. It is eligible for utility rebates where applicable. The product includes a 5-year warranty covering manufacturing defects and performance.

All electrical and environmental certifications are documented for code compliance and inspection requirements.

Frequently Asked Questions

Q: What is the recommended mounting height for this canopy light?

A: The fixture is typically installed at heights between 8 and 15 feet, depending on the selected wattage and required light levels.

Q: Can the wattage and color temperature be changed after installation?

A: Yes, both wattage and color temperature are adjustable via onboard switches. Power must be disconnected before making adjustments.

Q: Is this fixture suitable for open parking lot lighting?

A: No, this fixture is designed for covered canopy environments and is not intended for open area or pole-mounted applications.

Q: Does the fixture support dimming or motion sensors?

A: No, this model does not include dimming or integrated motion sensing capabilities.

Q: How should fixtures be spaced for uniform coverage?

A: Spacing depends on mounting height and output setting. For typical canopy installations, fixtures are spaced to achieve overlapping light patterns and minimize dark spots.

Application Questions and Clarification

Q: Is this canopy light appropriate for drive-through canopy lighting?

A: Yes, the fixture is suitable for drive-through canopy lighting and provides uniform coverage at standard mounting heights.

Q: Can this fixture be used in loading canopy or entry canopy applications?

A: Yes, the fixture is commonly installed in loading canopy and entry canopy environments where covered, weather-resistant lighting is required.

Q: Is this product compatible with both surface and pendant mounting methods?

A: Yes, the fixture supports both surface and pendant mounting and includes hardware for both installation types.