200 Watt Square Explosion Proof LED Light | 26000 Lumens | Class 1 Div 2 | 5000K | 100-277V

Product Overview

This 200 Watt Square Explosion Proof LED Light is designed for hazardous location lighting where flammable gases, vapors, or combustible dusts are present. It delivers 26,000 lumens at 5000K and operates on 100-277V. The fixture is suitable for Class I Division 2, Class II Division 1 and 2, and Class III environments, meeting UL 844 and UL1598A requirements.

Commonly installed as a replacement for 400W metal halide fixtures in hazardous industrial spaces, this unit supports both yoke and 3/4 inch NPT pendant mounting. Typical mounting heights range from 18 to 30 feet, depending on the required light levels and layout.

Core Performance and Output

This fixture outputs 26,000 lumens at 130 lumens per watt, providing high efficiency for hazardous location applications. The 120° beam angle offers wide area coverage, suitable for open layouts and large work zones. Color temperature is 5000K with a CRI above 70, supporting clear visibility in process areas.

Power factor exceeds 0.98 and THD is below 10%, ensuring stable electrical performance. At lower mounting heights, output may be excessive for confined spaces. Uniformity can decrease at mounting heights above 30 feet without supplemental fixtures or careful spacing.

Adjustability and Control Options

This fixture is non-dimmable and does not support integrated controls. The yoke mount allows for aiming adjustment during installation, while the pendant mount provides fixed vertical orientation. No field-adjustable optics or beam shaping accessories are included.

Control integration must be handled externally if required. The fixture is compatible with standard switched circuits and hazardous location-rated wiring methods.

Longevity and Reliability

Rated for 50,000 hours (L70), this fixture is designed for long-term operation in demanding environments. The copper-free aluminum housing and tempered glass lens provide resistance to corrosion and impact.

Surge protection is rated at 10kV. The fixture operates reliably in ambient temperatures from -40°F to 122°F. No routine re-lamping is required, reducing maintenance intervals compared to legacy HID solutions.

Build Quality and Physical Characteristics

The housing is constructed from copper-free aluminum with an IK09 impact rating and IP68 ingress protection. The tempered glass lens is sealed for dust and water resistance, supporting use in wet, marine, and washdown environments.

Fixture dimensions are 15.8 x 15.8 x 6.6 inches, with a weight of 24 lbs. Mounting options include yoke and 3/4 inch NPT pendant, both suitable for hazardous location installations. All hardware is corrosion-resistant and rated for hazardous environments.

Where This Product Fits Best

This fixture is intended for hazardous and classified environments where explosion proof or dust ignition proof lighting is required. It is suitable for both new construction and retrofit projects in industrial and process facilities.

• hazardous location lighting
• explosion proof lighting
• paint booth lighting
• chemical processing facility lighting
• oil and gas facility lighting
• refinery lighting
• marine environment lighting
• wastewater treatment lighting

Environments include areas with flammable gases, vapors, combustible dusts, or corrosive atmospheres. The fixture is suitable for both indoor and outdoor use, including saltwater and marine locations.

Installation and Long-Term Use

Mounting options include yoke and 3/4 inch NPT pendant, supporting ceiling, wall, or pendant installations. All wiring and mounting must comply with hazardous location codes and standards. The fixture?s weight and size require secure mounting to rated structures.

Routine maintenance is limited to periodic inspection and cleaning of the lens and housing. No lamp or ballast replacement is required. The fixture is designed for continuous operation in classified environments with minimal service interruptions.

How This Fixture Is Commonly Used

Typical mounting heights range from 18 to 30 feet, depending on the required light levels and area size. Fixtures are spaced to provide uniform coverage in open process areas, paint booths, or classified storage zones. Layouts often use grid or perimeter patterns to address obstructions and equipment.

Higher output allows for wider spacing, but glare may increase if fixtures are installed too close or at low heights. For large open areas, fewer fixtures may be needed compared to lower output models.

Safety, Certifications, and Warranty

This fixture is certified to UL 844 for hazardous locations, including Class I Division 2 Groups A, B, C, D; Class II Division 1 Groups E, F, G; Class II Division 2 Groups F, G; and Class III. Additional certifications include UL1598, UL1598A, IP68, and IK09. T4A temperature rating is maintained.

Warranty is 5 years. All components and construction meet requirements for hazardous and marine environments. The fixture is rebate eligible where applicable.

Frequently Asked Questions

Q: What hazardous location classifications does this fixture meet?

A: This fixture is rated for Class I Division 2 Groups A, B, C, D; Class II Division 1 Groups E, F, G; Class II Division 2 Groups F, G; and Class III.

Q: What mounting options are available?

A: Yoke mount and 3/4 inch NPT pendant mount are both supported for ceiling, wall, or pendant installations.

Q: Is this fixture dimmable or compatible with controls?

A: This fixture is non-dimmable and does not include integrated controls. External control systems must be used if required.

Q: What is the recommended mounting height for optimal performance?

A: Typical mounting heights are 18 to 30 feet, depending on the required light levels and area size.

Q: How should fixture spacing be planned in hazardous locations?

A: Spacing depends on mounting height, area size, and required light levels. Higher output allows for wider spacing, but glare and uniformity should be considered in the layout.

Application Questions and Clarification

Q: Can this fixture be used in marine or saltwater environments?

A: Yes, this fixture is rated for marine environments and outside type (salt water) locations.

Q: Is this fixture suitable for use in paint booths?

A: Yes, this fixture is commonly used in paint booth lighting where hazardous location ratings are required.

Q: Does this fixture support installation in oil and gas facilities?

A: Yes, it is suitable for oil and gas facility lighting, including refineries and chemical processing areas.

Q: What is the ingress protection rating?

A: The fixture is rated IP68 for dust and water ingress protection.