95 Watt LED Canopy Light | 12721 Lumens | 5000K | 100-277V

Product Overview

This 95 watt LED canopy light delivers 12,721 lumens at 5000K with a 134 lumens-per-watt efficiency. The fixture replaces 250 watt metal halide systems while drawing significantly less power. A 110-degree beam angle provides broad, even coverage across the mounting area.

The die-cast aluminum housing measures 17.1 x 17.1 x 4.1 inches and weighs 9 pounds. The white finish is standard. Surface mounting is the installation method for this fixture.

Operating voltage spans 100V to 277V at 50-60Hz, with a power factor above 0.90 and THD below 20%. The driver supports 1-10V dimming for output adjustment after installation.

Where This Product Fits Best

This canopy light is built for covered outdoor and semi-exposed locations where downward illumination is needed. Gas station canopies, parking structure ceilings, building entries, loading dock overhangs, and drive-through lanes are typical mounting locations.

The IP65 rating allows installation where the fixture will be exposed to rain, dust, and washdown from general cleaning. The operating temperature range of -22°F to 113°F supports use in climates with seasonal extremes.

At 12,721 lumens, this fixture suits applications where a single 250 watt metal halide fixture is currently installed or where similar light output is needed from a single mounting point.

Performance and Functional Considerations

The 5000K color temperature produces a neutral white light commonly used in commercial and retail-adjacent outdoor areas. CRI is rated at 70+, which is appropriate for general visibility and security lighting but may not suit applications requiring high color accuracy.

Rated lifespan is 50,000 hours at L70, meaning the fixture will maintain at least 70% of initial lumen output through that period. This reduces the frequency of lamp replacement cycles compared to metal halide systems.

The 1-10V dimming input allows output to be reduced when connected to a compatible dimming control. This is useful for sites that adjust light levels based on time of day or occupancy patterns.

Installation and Long-Term Use

The fixture mounts to a flat surface using the integrated mounting points on the housing. At 9 pounds, the weight is manageable for ceiling-mount applications without requiring additional structural reinforcement in most canopy deck assemblies.

The 100-277V input range covers standard commercial voltages. Verify site voltage before installation to confirm compatibility. Electrical connection should follow local codes and be performed by qualified personnel.

Die-cast aluminum construction resists corrosion in outdoor environments. The IP65 rating means the fixture can tolerate direct water jets from any direction, supporting periodic pressure washing of canopy surfaces without removal or protection of the fixture.

How This Fixture Is Commonly Used

Facilities use this fixture as a direct replacement for aging metal halide canopy lights. Once installed, the LED source eliminates restrike delay, so light is immediate on power-up rather than requiring warm-up time.

When connected to a 1-10V dimmer, operators can reduce output during low-traffic hours. This is often done at fueling stations, parking areas, or service entrances where full output is only needed during peak periods.

The 110-degree beam angle distributes light across a wide footprint beneath the fixture. In canopy applications, this typically means fewer fixtures are needed compared to narrower-beam alternatives to achieve consistent coverage across the ceiling grid.

Safety, Certifications, and Warranty

This fixture is UL listed. It is rebate eligible through applicable utility programs.

The IP65 rating allows the fixture to operate in wet and dusty environments without ingress affecting internal components. The operating temperature range of -22°F to 113°F defines the ambient conditions under which the fixture is rated to perform.

We provide a 5-year warranty on this fixture.

Frequently Asked Questions

What metal halide wattage does this fixture replace?
This fixture replaces 250 watt metal halide canopy lights.

What voltage does this fixture accept?
The fixture operates on 100V to 277V input at 50-60Hz.

Is this fixture rated for outdoor use?
Yes. The IP65 rating allows installation in wet and dusty outdoor locations.

Is dimming supported?
Yes. The fixture accepts 1-10V dimming input.

Is this fixture rebate eligible?
Yes. This fixture is rebate eligible through qualifying utility programs.

What is the warranty period?
This fixture carries a 5-year warranty.

Application Questions and Clarification

This product description reflects the provided specifications, ratings, and configuration options. For questions related to site-specific conditions, electrical compatibility, control integration, or application requirements not addressed in the provided data, our team is available to provide clarification.