2 Fixture 180 Degree Bullhorn Mount | 2 3/8 Inch Tenon | Bronze | Low Profile

Product Overview

This 2 Fixture 180 Degree Bullhorn Mount is designed for mounting two area or post top lighting fixtures in a 180-degree configuration. It fits standard 2 3/8 inch tenons and features a low-profile bronze finish. The mount is intended for use with compatible light poles in exterior environments where dual fixture orientation is required for wide area coverage or perimeter lighting.

Commonly used in parking lots, roadways, and commercial site lighting, this bullhorn mount supports two fixtures at opposite angles to maximize coverage from a single pole location. The EPA rating and weight are suitable for most standard steel or aluminum poles rated for area and site lighting applications.

Core Performance and Output

This bullhorn mount supports two fixtures in a 180-degree spread, allowing for broad, opposing light distribution from a single pole. The EPA (Effective Projected Area) is 1.0, which must be included in total EPA calculations for pole and foundation selection. The mount weighs 18 lbs and is compatible with fixtures designed for 2 3/8 inch tenon mounting.

Structural performance is suitable for most standard area lighting poles, but always confirm pole EPA and weight capacity before installation. Excessive fixture weight or high wind load conditions may require a higher-rated pole or additional engineering review.

Adjustability and Control Options

This bullhorn mount provides a fixed 180-degree orientation for two fixtures. Each arm is designed to accept a standard slipfitter or tenon-mount fixture. There is no built-in tilt or rotation adjustment beyond the fixture?s own mounting hardware.

Control options depend on the fixtures selected. The mount itself does not include integrated controls or wiring provisions beyond standard fixture mounting.

Longevity and Reliability

The mount is constructed for outdoor use with a durable bronze finish. It is designed to withstand typical environmental exposure in commercial and municipal settings. The 1-year warranty covers material and manufacturing defects.

Routine inspection of mounting hardware and finish is recommended, especially in coastal or high-corrosion environments. The mount?s reliability is dependent on proper installation and pole compatibility.

Build Quality and Physical Characteristics

This bullhorn mount is fabricated from robust materials and finished in bronze for corrosion resistance and visual consistency with most commercial poles and fixtures. The low-profile design minimizes wind load while supporting two fixtures securely.

It mounts to a standard 2 3/8 inch tenon and weighs 18 lbs. The EPA of 1.0 should be included in all structural calculations for pole selection and site engineering.

Where This Product Fits Best

This bullhorn mount is intended for exterior site lighting where dual fixture orientation is needed from a single pole. It is commonly used in environments requiring broad area coverage or perimeter illumination.

• parking lot lighting
• roadway lighting
• area lighting
• commercial site lighting
• sports facility lighting
• campus lighting
• industrial yard lighting
• dealership lighting

Suitable for outdoor installations where fixtures must be aimed in opposite directions. The bronze finish and low-profile design support use in both commercial and municipal settings. Not intended for use with poles or foundations not rated for the combined EPA and weight of mount plus fixtures.

Installation and Long-Term Use

The mount installs on a standard 2 3/8 inch tenon using set screws or bolts as specified by the manufacturer. Ensure all hardware is tightened to specification and that the pole is rated for the total EPA and weight of the mount and fixtures.

Long-term reliability depends on periodic inspection of mounting hardware and finish, especially in areas with high wind, vibration, or corrosive exposure. Re-torque hardware as part of routine maintenance schedules.

How This Fixture Is Commonly Used

This bullhorn mount is typically installed at mounting heights ranging from 15 to 30 feet, depending on fixture type and site requirements. Fixtures are spaced 180 degrees apart to provide wide, opposing coverage from a single pole location.

Layout patterns often use these mounts at pole locations along perimeters or in the center of large lots to reduce the number of poles needed. Using higher output fixtures can reduce fixture count but may increase glare or require careful aiming to avoid spill light.

Safety, Certifications, and Warranty

This mount is designed for outdoor use and is finished in bronze for corrosion resistance. The EPA and weight ratings must be observed for safe installation. No additional safety certifications are specified for this accessory.

The product includes a 1-year warranty covering defects in materials and workmanship. Follow all installation instructions and site engineering requirements for safe operation.

Frequently Asked Questions

Q: What is the maximum EPA and weight this bullhorn mount adds to a pole?

A: The mount has an EPA of 1.0 and weighs 18 lbs. Include these values in all pole and foundation calculations.

Q: What tenon size does this mount fit?

A: It is designed for standard 2 3/8 inch tenons.

Q: Can this mount be used with any area or shoebox fixture?

A: It is compatible with fixtures designed for 2 3/8 inch tenon mounting. Always confirm fixture weight and EPA are within pole limits.

Q: Is there any adjustability in the fixture orientation?

A: The mount provides a fixed 180-degree spread. Adjustability depends on the fixture?s own mounting hardware.

Q: How should I plan pole spacing when using this bullhorn mount?

A: Spacing depends on fixture output, mounting height, and site requirements. Dual fixtures at 180 degrees can increase coverage per pole but may require careful aiming to avoid overlap or dark spots.

Application Questions and Clarification

Q: Is this bullhorn mount suitable for sports facility lighting applications?

A: Yes, it is commonly used for sports facility lighting when dual fixture orientation is needed from a single pole.

Q: Can this mount be used in coastal or corrosive environments?

A: The bronze finish offers basic corrosion resistance, but additional inspection and maintenance are recommended in harsh environments.

Q: What is the recommended mounting height for this bullhorn mount?

A: Typical mounting heights range from 15 to 30 feet, depending on fixture type and site requirements.

Q: Does the mount include wiring provisions?

A: No, wiring provisions depend on the pole and fixture design. The mount provides mechanical support only.