76 / 105 / 125 Watt Adjustable Full Cutoff LED Wall Pack | 12000 to 19700 Lumens | 3000K / 4000K / 5000K Adjustable | 100-277V | Built-In Photocell | Bronze or White

Product Overview

This adjustable full cutoff LED wall pack is designed for exterior wall mounting on commercial and industrial buildings. It provides selectable wattage and color temperature, allowing adaptation to site-specific requirements. Typical use cases include replacing 400W metal halide wall packs on building perimeters, service areas, and entry points at mounting heights from 8 to 20 feet.

The fixture includes a built-in photocell for dusk-to-dawn operation and is available in bronze or white finishes. The housing is die-cast aluminum with an IP65 rating for weather resistance in exposed outdoor environments.

Core Performance and Output

This wall pack delivers three selectable output levels: 12,000, 16,800, or 19,700 lumens, with efficacy between 156 and 160 lumens per watt. The full cutoff optical design provides forward-throw distribution while minimizing uplight and glare. Color temperature can be set to 3000K, 4000K, or 5000K to match site requirements or existing lighting.

Performance is suitable for perimeter security, building facade, and entry lighting at standard wall pack mounting heights. Output may be excessive for small entryways or low mounting positions below 8 feet. Uniformity can be affected if spacing exceeds typical wall pack intervals.

Adjustability and Control Options

Wattage and color temperature are field adjustable using onboard switches, allowing tuning during installation or future maintenance. The integrated photocell enables automatic dusk-to-dawn operation without external controls. No dimming function is provided.

Adjustability supports adaptation to changing site needs, such as energy reduction or color matching after installation. Photocell can be bypassed if required for switched operation.

Longevity and Reliability

The fixture is rated for 50,000 hours (L70) at typical operating temperatures. The die-cast aluminum housing and polycarbonate lens provide impact resistance and protection against vandalism. Operating temperature range is -40°F to 113°F, suitable for most North American climates.

Surge protection is rated at 4kV. The fixture is UL listed and IP65 rated for wet locations. No routine re-lamping is required; maintenance is limited to periodic cleaning and inspection.

Build Quality and Physical Characteristics

The fixture measures 14.33 inches long, 9.25 inches high, and 7 inches deep, with a weight of 12 lbs. The housing is die-cast aluminum with a powder-coated finish in bronze or white. The lens is polycarbonate for impact resistance and optical clarity.

All wiring and adjustment points are accessible from the rear after removing the housing from the wall. The fixture is designed for direct wall mounting over standard junction boxes or conduit entries.

Where This Product Fits Best

This wall pack is intended for exterior wall mounting on commercial and industrial buildings where full cutoff optics, adjustable output, and color flexibility are required. It is commonly used for perimeter security, building entrances, and service areas.

• security lighting
• building facade lighting
• building exterior lighting
• commercial exterior wall lighting
• perimeter lighting
• entry lighting
• service area lighting
• loading area lighting

Suitable for wet locations and environments exposed to weather, vandalism, or frequent use. Not intended for canopy, flood, or area lighting applications.

Installation and Long-Term Use

Designed for direct wall mounting using standard hardware. The fixture can be installed over existing junction boxes or surface conduit entries. All adjustments for wattage and color temperature are made before final closure of the housing.

Routine maintenance is limited to cleaning the lens and inspecting seals. The integrated photocell reduces manual intervention for daily operation. No lamp changes are required over the rated life. Ensure mounting surface supports the 12 lb fixture weight.

How This Fixture Is Commonly Used

Typical mounting heights range from 8 to 20 feet, depending on output setting and site requirements. Fixtures are spaced to provide overlapping coverage along building perimeters, with closer spacing at entry points or high-traffic areas.

Higher output settings reduce the number of fixtures needed for uniform coverage but may increase glare if mounted at lower heights. Adjustability allows tuning after installation to balance light levels and energy use.

Safety, Certifications, and Warranty

This fixture is UL listed and IP65 rated for wet locations. Surge protection is rated at 4kV. The product is eligible for utility rebates where applicable. A 5-year warranty covers manufacturing defects and performance.

All components are rated for outdoor use and exposure to weather. No hazardous materials are present in the construction.

Frequently Asked Questions

Q: What is the recommended mounting height for this wall pack?

A: Typical mounting heights are 8 to 20 feet, depending on output setting and site requirements.

Q: Can the color temperature and wattage be changed after installation?

A: Yes, both color temperature and wattage are field adjustable using onboard switches inside the housing.

Q: Is this fixture suitable for use in wet locations?

A: Yes, the fixture is IP65 rated for wet locations and outdoor exposure.

Q: Does the integrated photocell support dusk-to-dawn operation?

A: Yes, the built-in photocell enables automatic dusk-to-dawn operation. It can be bypassed if switched control is required.

Q: How should fixtures be spaced for perimeter lighting?

A: Spacing depends on mounting height and output setting. For uniform coverage, fixtures are typically spaced 2 to 3 times the mounting height apart.

Application Questions and Clarification

Q: Is this wall pack appropriate for entry lighting on multifamily buildings?

A: Yes, it is commonly used for entry lighting and multifamily exterior lighting where full cutoff and adjustable output are needed.

Q: Can this fixture be used for loading area lighting?

A: Yes, it is suitable for loading area lighting when mounted on exterior walls at appropriate heights.

Q: Is this fixture intended for flood or area lighting applications?

A: No, this wall pack is designed for wall-mounted exterior lighting, not for flood or area lighting use.