70 Watt Full Cutoff Half Moon LED Wall Pack | 9445 Lumens | 4000K or 5000K | 100-277V | Built-In Photocell

Product Overview

The 70 Watt Full Cutoff Half Moon LED Wall Pack is designed for exterior wall mounting on commercial and industrial buildings. This fixture delivers 9445 lumens at either 4000K or 5000K, providing a high-output solution for perimeter and security lighting. The full cutoff design minimizes uplight and glare, supporting compliance with dark sky requirements in many jurisdictions.

This wall pack is commonly used as a direct replacement for 250W metal halide wall packs. Typical mounting heights range from 8 to 18 feet, making it suitable for building exteriors, service areas, and loading zones where uniform, controlled illumination is required.

Core Performance and Output

This fixture outputs 9445 lumens at 70 watts, achieving an efficacy of 135 lumens per watt. The 90° beam angle provides a forward-throw distribution, supporting wide coverage along building perimeters and entry points. Color temperature options include 4000K and 5000K, both with a minimum CRI of 70 for general exterior visibility.

Electrical performance is stable across 100-277V input, with a power factor above 0.90 and THD below 20%. At mounting heights below 8 feet, output may be excessive for pedestrian areas. Uniformity can decrease if spacing exceeds typical wall pack intervals along long building facades.

Adjustability and Control Options

This wall pack includes a built-in photocell for dusk-to-dawn operation, reducing manual intervention and supporting energy management. 1-10V dimming is available for integration with compatible controls, allowing for scheduled or occupancy-based dimming if required by the site.

There are no field-adjustable optics or tilt features. The fixture is designed for fixed wall mounting with a full cutoff distribution. Photocell can be bypassed if not needed for the application.

Longevity and Reliability

The fixture is rated for 70,000 hours of L70 life, supporting long-term deployment with minimal maintenance. The LED driver and light engine are thermally managed within a die-cast aluminum housing, reducing risk of premature failure in typical outdoor environments.

Operating temperature range is -22°F to 113°F. The IP65 rating protects against dust and water ingress, supporting reliable operation in exposed exterior locations. Routine cleaning of the lens and housing is recommended to maintain output and appearance.

Build Quality and Physical Characteristics

The housing is constructed from die-cast aluminum with a bronze finish, providing durability and corrosion resistance. The polycarbonate lens is impact-resistant and designed for outdoor use. The fixture measures 14 x 7.5 x 7.5 inches and weighs 7.5 lbs, supporting secure mounting on standard masonry or concrete walls.

All wiring and connections are protected within the housing. The fixture is designed for direct wall mounting using standard hardware. No additional brackets or accessories are required for typical installations.

Where This Product Fits Best

This wall pack is intended for exterior wall mounting on commercial and industrial buildings where controlled, high-output lighting is required. It is suitable for both new construction and retrofit projects replacing legacy metal halide wall packs.

• security lighting
• building facade lighting
• building exterior lighting
• commercial exterior wall lighting
• perimeter lighting
• entry lighting
• service area lighting
• loading area lighting

Environments include warehouses, manufacturing facilities, retail buildings, and multifamily properties. The IP65 rating and full cutoff design support use in exposed locations with moderate weather exposure.

Installation and Long-Term Use

The fixture is designed for direct wall mounting using standard anchors and hardware. Electrical connections are made within the housing, supporting 100-277V input. The built-in photocell can be enabled or bypassed as required by site controls.

Routine inspection is recommended to ensure lens clarity and housing integrity. The die-cast construction and IP65 rating minimize maintenance requirements. Replacement of the entire fixture is typical at end of life, as the LED array and driver are not field-serviceable.

How This Fixture Is Commonly Used

Typical mounting heights range from 8 to 18 feet, depending on the area to be illuminated and required light levels. Fixtures are commonly spaced 20 to 30 feet apart along building facades, entries, and service areas to achieve uniform coverage.

Higher output allows for wider spacing, but may increase glare if installed at low mounting heights or near pedestrian pathways. Layouts should consider site-specific requirements for security, visibility, and compliance with local lighting ordinances.

Safety, Certifications, and Warranty

This fixture is UL listed and IP65 rated. It meets requirements for use in wet locations and is eligible for utility rebate programs where applicable. The product is covered by a 5-year warranty from the date of installation.

No special safety procedures are required beyond standard electrical and ladder safety during installation. The fixture is suitable for use on non-combustible building exteriors and does not require additional shielding or guards.

Frequently Asked Questions

Q: What is the recommended mounting height for this wall pack?

A: Typical mounting heights are 8 to 18 feet, depending on the area and required light levels.

Q: Can the built-in photocell be disabled if not needed?

A: Yes, the photocell can be bypassed during installation if dusk-to-dawn operation is not required.

Q: Is this fixture suitable for use in wet or exposed outdoor locations?

A: Yes, the IP65 rating supports use in wet and exposed exterior environments.

Q: What is the expected lifespan of the LEDs and driver?

A: The fixture is rated for 70,000 hours of L70 life under normal operating conditions.

Q: How should fixtures be spaced along a building facade?

A: Spacing typically ranges from 20 to 30 feet, depending on mounting height and desired uniformity.

Application Questions and Clarification

Q: Is this wall pack appropriate for entry lighting on multifamily buildings?

A: Yes, this fixture is commonly used for entry lighting and multifamily exterior wall applications.

Q: Can this fixture be used for perimeter lighting around a warehouse?

A: Yes, it is suitable for perimeter lighting on commercial and industrial building exteriors.

Q: Does the full cutoff design help with dark sky compliance?

A: The full cutoff design minimizes uplight and supports compliance with dark sky requirements in many areas.

Q: Is this fixture suitable for use in loading area lighting?

A: Yes, it is frequently installed for loading area and service area lighting on building exteriors.