63 / 90 / 108 Watt Adjustable Semi Cutoff LED Wall Pack | 8800 to 14500 Lumens | 3000K / 4000K / 5000K Adjustable | 100-277V | Built-In Photocell

Product Overview

This adjustable semi cutoff LED wall pack is designed for exterior wall mounting where reliable, high-output illumination is needed. The fixture supports selectable wattages of 63, 90, or 108 watts, delivering up to 14,500 lumens. Color temperature can be set to 3000K, 4000K, or 5000K at installation. The built-in photocell enables dusk-to-dawn operation without additional controls.

Commonly used as a direct replacement for 400W metal halide wall packs, this unit is suitable for mounting heights between 8 and 20 feet on building exteriors. The die-cast aluminum housing and polycarbonate lens provide durability in demanding environments, including areas with vandalism risk or frequent exposure to weather.

Core Performance and Output

This wall pack offers three selectable output levels: 8,800, 12,000, or 14,500 lumens, with an efficacy of 134 lumens per watt. The semi cutoff design provides forward-throw distribution, balancing perimeter coverage with reduced uplight. Color temperature can be field-adjusted to 3000K, 4000K, or 5000K to match site requirements.

Power factor exceeds 0.9, and total harmonic distortion is below 20%. The fixture operates on 100-277V input at 50/60Hz. Output at the highest wattage may be excessive for low mounting heights or narrow walkways, and uniformity may decrease if spacing exceeds typical wall pack intervals.

Adjustability and Control Options

Wattage and color temperature are both adjustable via onboard switches, allowing field selection during installation or maintenance. The integrated photocell provides automatic dusk-to-dawn operation, eliminating the need for external controls or timers.

No dimming function is provided. The fixture is intended for applications where full output is required during hours of darkness, and where simple, reliable control is preferred over advanced networked options.

Longevity and Reliability

The fixture is rated for 50,000 hours (L70) at typical operating conditions. The die-cast aluminum housing and polycarbonate lens resist impact and vandalism. IP65 ingress protection ensures reliable operation in wet or dusty environments.

Operating temperature range is -40°F to 113°F. Surge protection is rated at 4kV. The fixture is designed for long-term exterior use with minimal maintenance requirements.

Build Quality and Physical Characteristics

The housing is constructed from die-cast aluminum with a bronze finish. The lens is polycarbonate for impact resistance. The fixture measures 14.3 x 9.3 x 5.9 inches and weighs 8 lbs, supporting secure wall mounting on masonry, concrete, or structural exterior walls.

All wiring and adjustment points are accessible from the rear or underside of the housing. The fixture is designed for direct wall mounting with standard hardware. The semi cutoff form factor provides a balance of forward throw and glare control.

Where This Product Fits Best

This wall pack is intended for exterior wall mounting on commercial and industrial buildings. It is suitable for locations requiring robust, high-output lighting with selectable color and wattage. Typical environments include building perimeters, service areas, and entry points where vandal resistance and weather protection are priorities.

• security lighting
• building facade lighting
• building exterior lighting
• commercial exterior wall lighting
• perimeter lighting
• entry lighting
• service area lighting
• loading area lighting

The fixture is IP65 rated for wet locations and is suitable for use in areas exposed to rain, dust, or debris. It is not intended for hazardous locations or marine environments.

Installation and Long-Term Use

This wall pack mounts directly to exterior walls using standard anchors and hardware. All adjustments for wattage and color temperature are made before final closure of the housing. The integrated photocell simplifies wiring and reduces the need for additional controls.

Routine maintenance is limited to periodic cleaning of the lens and inspection of seals. The fixture is designed for minimal service requirements over its rated life. Replacement of the entire unit is typical at end of life, as internal components are not field-serviceable.

How This Fixture Is Commonly Used

Typical mounting heights range from 8 to 20 feet, depending on output setting and site requirements. Fixtures are spaced to provide overlapping coverage along building perimeters, entryways, or service areas. Layouts often use higher output settings for wider coverage or increased security.

Spacing and mounting height should be coordinated with output selection to avoid excessive brightness or glare. Higher output settings can reduce fixture count but may require careful aiming or shielding in pedestrian areas.

Safety, Certifications, and Warranty

This fixture is UL listed and IP65 rated. Surge protection is rated at 4kV. The product is eligible for utility rebates where applicable. Warranty coverage is 5 years from date of installation.

All certifications and ratings are stated as provided by the manufacturer. The fixture is suitable for use in wet locations and meets standard requirements for commercial exterior lighting.

Frequently Asked Questions

Q: What is the recommended mounting height for this wall pack?

A: Typical mounting heights are 8 to 20 feet, depending on output setting and area coverage requirements.

Q: How do I adjust the wattage and color temperature?

A: Both wattage and color temperature are set using onboard switches inside the housing before final installation.

Q: Is this fixture dimmable or compatible with external controls?

A: This fixture does not support dimming and is intended for use with its integrated photocell for dusk-to-dawn operation.

Q: What is the expected lifespan and maintenance requirement?

A: The fixture is rated for 50,000 hours (L70) and requires only periodic cleaning and inspection. Internal components are not field-serviceable.

Q: How should I plan fixture spacing for perimeter lighting?

A: Spacing depends on mounting height and output setting. For uniform coverage, fixtures are typically spaced 2 to 3 times the mounting height apart, with adjustments based on site layout and security needs.

Application Questions and Clarification

Q: Is this wall pack suitable for use in loading area lighting?

A: Yes, the fixture is commonly used for loading area lighting where robust, high-output exterior illumination is required.

Q: Can this fixture be used for multifamily exterior lighting?

A: The fixture is suitable for multifamily exterior lighting, especially in areas where vandal resistance and weather protection are important.

Q: Is this product appropriate for alley lighting applications?

A: Yes, this wall pack is used in alley lighting where wall-mounted, directional exterior lighting is needed.

Q: Does the fixture support installation in wet or exposed environments?

A: The fixture is IP65 rated and designed for use in wet locations and exposed exterior environments.