60 Watt Full Cutoff LED Wall Pack | 7600 Lumens | 5000K | 100-277V

Product Overview

The 60 Watt Full Cutoff LED Wall Pack is designed for exterior wall mounting where controlled, efficient illumination is required. This fixture delivers 7600 lumens at 5000K, providing a neutral white light suitable for security and architectural lighting on commercial and industrial buildings. The full cutoff design minimizes uplight and glare, supporting compliance with light pollution requirements in many jurisdictions.

This wall pack is commonly installed at building perimeters, entry points, and service areas, replacing legacy 150W metal halide units. Typical mounting heights range from 8 to 15 feet, making it suitable for low to mid-rise building exteriors and site perimeters.

Core Performance and Output

This fixture outputs 7600 lumens at 60 watts, achieving an efficacy of 127 lumens per watt. The 140° beam angle provides wide, uniform coverage along building facades and adjacent walkways. The 5000K color temperature delivers clear visibility for security and general exterior tasks.

Electrical performance includes 100-277V input, a power factor above 0.90, and total harmonic distortion below 20%. At mounting heights below 8 feet, output may be excessive for pedestrian-only areas. At heights above 15 feet, uniformity and ground-level illumination may decrease.

Adjustability and Control Options

The fixture supports 1-10V dimming for integration with compatible controls or building automation systems. This allows for scheduled dimming, occupancy-based control, or daylight harvesting where required. The full cutoff optical design directs light downward and outward, reducing spill and glare.

No field-adjustable beam or color temperature options are included. The fixture is intended for fixed wall mounting with a set distribution pattern.

Longevity and Reliability

The LED system is rated for 50,000 hours (L70), supporting multi-year operation with minimal maintenance. The die-cast aluminum housing and polycarbonate lens provide resistance to impact and weather exposure.

Operating temperature range is -40°F to 113°F, suitable for most North American climates. The fixture is IP65 rated for dust and water ingress protection, supporting reliable use in exposed exterior environments.

Build Quality and Physical Characteristics

The housing is constructed from die-cast aluminum with a bronze finish for corrosion resistance. The polycarbonate lens is impact-resistant and designed to maintain optical clarity over time. Fixture dimensions are 10.9 x 6.9 x 4.9 inches, with a weight of 3.9 lbs, supporting straightforward handling during installation.

All hardware is designed for direct wall mounting. The compact form factor allows installation in areas with limited wall space or architectural constraints.

Where This Product Fits Best

This wall pack is intended for exterior wall mounting on commercial and industrial buildings where controlled, efficient lighting is required for safety, security, and architectural visibility. It is suitable for use on building perimeters, entryways, and service areas where moderate to high light levels are needed.

• security lighting
• building facade lighting
• building exterior lighting
• commercial exterior wall lighting
• perimeter lighting
• entry lighting
• service area lighting
• multifamily exterior lighting

IP65 rating and ETL certification support use in wet locations and exposed environments. The fixture is not intended for canopy, high mast, or hazardous location applications.

Installation and Long-Term Use

The fixture is designed for direct wall mounting using standard hardware. Electrical connection is made via 100-277V input, compatible with most commercial building circuits. The compact size and moderate weight allow for single-person installation in most cases.

Routine maintenance is limited to periodic cleaning of the lens and inspection of mounting hardware. No relamping is required. The fixture is suitable for retrofit or new construction where full cutoff performance and low maintenance are priorities.

How This Fixture Is Commonly Used

Typical mounting heights range from 8 to 15 feet, depending on the required coverage and site geometry. Fixtures are often spaced 15 to 30 feet apart along building facades or perimeter walls to achieve uniform illumination and minimize dark spots.

In security applications, higher output may reduce the number of fixtures needed but can increase glare if mounted too low. For entry and service areas, placement is typically coordinated with doorways and access points to ensure adequate visibility.

Safety, Certifications, and Warranty

This fixture is ETL certified and IP65 rated. It is suitable for wet locations and meets requirements for exterior commercial lighting. The product is listed as rebate eligible in many utility programs.

A 5-year warranty covers manufacturing defects and LED performance. The fixture is designed to operate safely within the specified temperature and voltage ranges.

Frequently Asked Questions

Q: What is the recommended mounting height for this wall pack?

A: Recommended mounting height is 8 to 15 feet for optimal coverage and uniformity.

Q: Can this fixture be used with occupancy sensors or dimming controls?

A: Yes, it supports 1-10V dimming and can be integrated with compatible controls.

Q: Is this fixture suitable for wet locations?

A: Yes, it is IP65 rated for wet and exposed exterior environments.

Q: What type of lens material is used?

A: The fixture uses a polycarbonate lens for impact resistance and optical clarity.

Q: How many fixtures are needed for a 100-foot building facade?

A: Spacing typically ranges from 15 to 30 feet, so 4 to 7 fixtures are common for a 100-foot facade, depending on required light levels.

Application Questions and Clarification

Q: Is this wall pack appropriate for loading area lighting?

A: Yes, it is commonly used for loading area lighting when mounted at appropriate heights for the space.

Q: Can this fixture be installed on multifamily residential exteriors?

A: Yes, it is suitable for multifamily exterior lighting, including entryways and perimeter walls.

Q: Is this fixture intended for hazardous or classified locations?

A: No, it is not rated for hazardous or classified environments.

Q: Does the full cutoff design help with dark sky compliance?

A: The full cutoff design minimizes uplight and glare, supporting compliance with many dark sky requirements.