30 Watt Full Cutoff LED Wall Pack | 3700 Lumens | 5000K | 100-277V

Product Overview

The 30 Watt Full Cutoff LED Wall Pack is designed for exterior wall mounting where controlled, efficient illumination is required. This fixture delivers 3700 lumens at 5000K, providing a neutral white light suitable for security and architectural lighting on commercial and multifamily buildings. The full cutoff design minimizes uplight and glare, supporting compliance with dark sky requirements in many jurisdictions.

This wall pack is a direct replacement for 70W metal halide units, offering improved energy efficiency and reduced maintenance. Typical mounting heights range from 8 to 12 feet, making it suitable for perimeter walls, entryways, and service areas on low- to mid-rise structures.

Core Performance and Output

This fixture outputs 3700 lumens at 123 lumens per watt, providing effective coverage for building exteriors, entry points, and walkways. The 140° beam angle delivers wide, uniform illumination along wall surfaces and adjacent ground areas. Color temperature is 5000K, supporting visibility and security tasks.

Electrical performance includes 100-277V input, 1-10V dimming, and a power factor above 0.90. At mounting heights above 12 feet, light levels may decrease and uniformity can be reduced. Excessive output may occur if installed below 8 feet, potentially increasing glare for pedestrians.

Adjustability and Control Options

The fixture supports 1-10V dimming for integration with compatible lighting controls or building automation systems. This allows for scheduled dimming, occupancy-based control, or daylight harvesting where required. The full cutoff optical design directs light downward and outward, with no adjustable aiming or tilt features.

No integrated photocell or motion sensor is included. External controls can be added at the circuit or system level if needed for energy management or code compliance.

Longevity and Reliability

The LED system is rated for 50,000 hours (L70), supporting long-term operation with minimal maintenance. The die-cast aluminum housing and polycarbonate lens provide resistance to impact and environmental exposure. The fixture is IP65 rated for protection against dust and water jets, suitable for outdoor installation in most climates.

Operating temperature range is -40°F to 122°F. No routine relamping is required. Periodic cleaning of the lens and inspection of mounting hardware is recommended for optimal performance.

Build Quality and Physical Characteristics

The fixture housing is constructed from die-cast aluminum with a bronze finish. The polycarbonate lens is impact-resistant and UV-stabilized to prevent yellowing. Overall dimensions are 7.6 x 9.4 x 3.9 inches, with a total weight of 3.4 lbs. The compact form factor supports installation in tight spaces or on architectural features.

All wiring and mounting points are accessible from the rear. The fixture is designed for direct wall mounting using standard hardware. No special tools are required for installation.

Where This Product Fits Best

This wall pack is intended for exterior wall mounting on commercial, multifamily, and institutional buildings. It is suitable for applications requiring controlled, uniform illumination with minimal uplight. The fixture is commonly used for:

• building facade lighting
• security lighting
• commercial exterior wall lighting
• building exterior lighting
• perimeter lighting
• entry lighting
• service area lighting
• multifamily exterior lighting

IP65 rating supports use in wet locations and exposed environments. The fixture is not intended for canopy, pole, or high-mast mounting. For optimal results, install at heights appropriate for the output level and beam distribution.

Installation and Long-Term Use

This fixture mounts directly to exterior walls using standard anchors and hardware. All wiring is completed through the rear housing. The compact size allows for installation on masonry, concrete, or metal surfaces without extensive preparation.

Routine maintenance is limited to cleaning the lens and checking for debris or obstructions. The sealed housing prevents water ingress and minimizes insect intrusion. For long-term reliability, verify that mounting surfaces remain secure and that the fixture is not exposed to corrosive chemicals or physical impact.

How This Fixture Is Commonly Used

Typical mounting heights are 8 to 12 feet above grade, spaced 15 to 25 feet apart depending on required light levels and site geometry. Fixtures are often installed above entry doors, along walkways, or at building corners to provide perimeter coverage.

Spacing and layout should be adjusted based on the desired uniformity and the presence of architectural features. Higher output can reduce the number of fixtures needed, but may increase glare if installed too low or too close together.

Safety, Certifications, and Warranty

This fixture is ETL certified and IP65 rated. It meets requirements for wet location installation and is eligible for utility rebate programs where applicable. The product includes a 5-year warranty covering manufacturing defects and LED performance.

No hazardous materials are present in the construction. All components are rated for outdoor use and comply with relevant safety standards.

Frequently Asked Questions

Q: What is the recommended mounting height for this wall pack?

A: Mounting heights between 8 and 12 feet provide effective coverage and minimize glare for most exterior wall applications.

Q: Can this fixture be used with a photocell or motion sensor?

A: The fixture does not include integrated sensors, but it is compatible with external photocells or motion sensors installed at the circuit or system level.

Q: Is this wall pack suitable for use in wet locations?

A: Yes, the fixture is IP65 rated and designed for outdoor wet location use.

Q: How many fixtures are needed for continuous wall coverage?

A: Spacing fixtures 15 to 25 feet apart is typical, but actual fixture count depends on site geometry and required light levels.

Application Questions and Clarification

Q: Is this fixture appropriate for lighting building entrances and walkways?

A: Yes, the output and beam distribution are suitable for entry lighting and walkway illumination on commercial and multifamily buildings.

Q: Can this wall pack be used for perimeter security lighting?

A: The fixture is commonly installed for perimeter lighting and security coverage along exterior walls.

Q: Is this product intended for pole or canopy mounting?

A: No, this fixture is designed for direct wall mounting only and is not suitable for pole or canopy applications.