30 Watt Full Cutoff LED Wall Pack | 4000 Lumens | 3000K / 4000K / 5000K Adjustable | 100-277V | Built-In Photocell

Product Overview

This 30 Watt Full Cutoff LED Wall Pack is designed for exterior wall mounting on commercial and industrial buildings. It delivers 4000 lumens with selectable color temperature options of 3000K, 4000K, or 5000K. The fixture is intended for perimeter illumination, security lighting, and architectural accenting where controlled light distribution and energy efficiency are required. Typical mounting heights range from 8 to 14 feet, making it a direct replacement for 100W to 150W metal halide wall packs in similar applications.

The fixture includes a built-in photocell for dusk-to-dawn operation and is suitable for use in environments exposed to rain, dust, and temperature fluctuations. The full cutoff design minimizes uplight and glare, supporting compliance with dark sky requirements in many jurisdictions.

Core Performance and Output

This wall pack outputs 4000 lumens at 30 watts, providing an efficacy of 133 lumens per watt. The 120° beam angle delivers wide, uniform coverage along building exteriors and entry points. Color temperature can be field-selected between 3000K, 4000K, and 5000K to match site requirements or existing lighting.

0-10V dimming is standard, allowing integration with compatible controls for further energy management. At mounting heights below 8 feet, output may be excessive for pedestrian-only areas. At heights above 14 feet, uniformity and ground-level illumination may decrease.

Adjustability and Control Options

The fixture features a field-adjustable CCT switch, enabling selection of 3000K, 4000K, or 5000K during installation or maintenance. This supports adaptation to changing site needs or color matching with other exterior luminaires. The built-in photocell provides automatic dusk-to-dawn operation without the need for external controls.

0-10V dimming capability is included for integration with building lighting control systems. No motion sensor is included as standard. The fixture does not support wireless controls or networked lighting protocols.

Longevity and Reliability

The LED system is rated for 50,000 hours (L70), supporting multi-year operation with minimal maintenance. The die-cast aluminum housing and polycarbonate lens are designed for durability in outdoor environments, including exposure to rain, wind, and airborne debris.

Operating temperature range is -40°F to 122°F. The fixture is IP65 rated for protection against dust and water ingress. No routine re-lamping is required, and the integrated driver is designed for long-term reliability.

Build Quality and Physical Characteristics

The fixture housing is constructed from die-cast aluminum with a black finish. The lens is polycarbonate for impact resistance and UV stability. Overall dimensions are 9.2 x 7.7 x 4.7 inches, and the fixture weight is 4.3 lbs.

All wiring and mounting hardware are accessible from the rear, supporting standard wall mounting over existing junction boxes. The fixture is designed for flush installation against flat exterior surfaces. Power factor is greater than 0.90, and total harmonic distortion is less than 20%.

Where This Product Fits Best

This wall pack is suited for exterior wall mounting on commercial and industrial buildings where moderate output and full cutoff distribution are required. It is commonly used for perimeter illumination, security, and architectural accenting at entry points and service areas.

• security lighting
• building facade lighting
• building exterior lighting
• commercial exterior wall lighting
• perimeter lighting
• entry lighting
• service area lighting
• multifamily exterior lighting

Suitable for wet locations and environments with temperature swings. Not intended for canopy, pole, or high-mount area lighting applications.

Installation and Long-Term Use

The fixture is designed for direct wall mounting using standard hardware. It can be installed over existing electrical boxes or surface conduit entries. The compact form factor supports retrofit and new construction scenarios where space is limited.

Routine maintenance is limited to periodic cleaning of the lens and housing. The built-in photocell reduces manual intervention for daily operation. All adjustments, including CCT selection, are accessible without fixture removal.

How This Fixture Is Commonly Used

Typical mounting heights are 8 to 14 feet above grade, spaced 15 to 30 feet apart depending on required light levels and site geometry. Fixtures are often installed at building entrances, loading areas, and along exterior walkways for security and visibility.

Spacing and layout should be adjusted based on wall geometry and the presence of architectural features. Higher output reduces fixture count but may increase glare if mounted too low or near reflective surfaces.

Safety, Certifications, and Warranty

This fixture is UL listed and IP65 rated. It meets requirements for wet location installation and is eligible for utility rebates where applicable. The product is covered by a 5-year warranty from the date of installation.

No special safety procedures are required beyond standard electrical and ladder safety during installation. The fixture is suitable for use in commercial, industrial, and multifamily exterior environments.

Frequently Asked Questions

Q: What is the recommended mounting height for this wall pack?

A: Recommended mounting height is 8 to 14 feet above grade for optimal coverage and uniformity.

Q: Can the color temperature be changed after installation?

A: Yes, the color temperature can be field-adjusted between 3000K, 4000K, and 5000K using the internal switch.

Q: Is the built-in photocell optional or always active?

A: The built-in photocell is always active and controls dusk-to-dawn operation unless bypassed during wiring.

Q: Does this fixture support motion sensors or wireless controls?

A: No, this fixture does not include motion sensors or wireless control capability.

Q: How many fixtures are needed for a 100-foot building facade?

A: For typical spacing of 20 to 25 feet, 4 to 5 fixtures are required for uniform coverage along a 100-foot facade.

Application Questions and Clarification

Q: Is this wall pack suitable for use in loading area lighting?

A: Yes, this fixture is commonly used for loading area lighting when mounted at appropriate heights for the space.

Q: Can this fixture be installed in multifamily exterior lighting applications?

A: Yes, it is suitable for multifamily exterior lighting, including entryways and perimeter walls.

Q: Is this fixture appropriate for perimeter lighting around commercial buildings?

A: Yes, it is designed for perimeter lighting on commercial building exteriors.

Q: Is this wall pack intended for canopy or pole mounting?

A: No, this fixture is designed for direct wall mounting only and is not intended for canopy or pole applications.