30 / 45 / 63 Watt Adjustable Semi Cutoff LED Wall Pack | 4200 to 8800 Lumens | 3000K / 4000K / 5000K Adjustable | 100-277V | Built-In Photocell

Product Overview

This adjustable semi cutoff LED wall pack is designed for exterior wall mounting in commercial and industrial environments. The fixture offers selectable wattage settings of 30, 45, or 63 watts, delivering up to 8800 lumens. It is suitable for replacing legacy 250W metal halide wall packs on building exteriors, perimeter walls, and service areas.

Color temperature can be set to 3000K, 4000K, or 5000K to match site requirements. The integrated photocell supports dusk-to-dawn operation. Typical mounting heights range from 8 to 18 feet, depending on output selection and site layout.

Core Performance and Output

This wall pack provides three selectable output levels: 4200, 6300, or 8800 lumens, with an efficacy of 134 lumens per watt. The semi cutoff design delivers forward-throw distribution for perimeter and pathway illumination while reducing uplight. The fixture operates on 100-277V input and maintains a power factor above 0.9 with total harmonic distortion below 20%.

At the highest output, mounting below 10 feet may result in excessive brightness and increased glare. Uniformity may decrease at mounting heights above 18 feet, especially in wide open areas.

Adjustability and Control Options

Wattage and color temperature are field adjustable using onboard switches. The fixture can be set to 30W, 45W, or 63W, and 3000K, 4000K, or 5000K CCT. An integrated photocell enables automatic dusk-to-dawn operation. No dimming or networked control options are included.

Adjustability allows adaptation to site-specific requirements during installation or future changes in use. The fixture is not compatible with external dimming systems.

Longevity and Reliability

The fixture is rated for 50,000 hours (L70) and includes a 5-year warranty. The die-cast aluminum housing and polycarbonate lens provide impact resistance and durability in exterior environments. Surge protection is rated at 4kV.

Operating temperature range is -40°F to 113°F. The fixture is suitable for year-round outdoor use in most climates.

Build Quality and Physical Characteristics

The housing is constructed from die-cast aluminum with a bronze finish. The lens is polycarbonate for vandal resistance. The fixture measures 14.3 x 9.3 x 5.6 inches and weighs 6.2 lbs.

IP65 rating protects against dust and water ingress. The fixture is designed for direct wall mounting using standard hardware. All wiring and adjustment points are accessible from the rear or side of the housing.

Where This Product Fits Best

This wall pack is intended for exterior wall mounting on commercial and industrial buildings. It is commonly used to provide perimeter, entry, and security lighting in areas requiring vandal resistance and reliable dusk-to-dawn operation.

• security lighting
• building facade lighting
• building exterior lighting
• commercial exterior wall lighting
• perimeter lighting
• entry lighting
• service area lighting
• loading area lighting

Suitable for wet locations and exposed exterior walls. Not intended for canopy, pole, or ceiling mounting. Performance is optimized for wall heights between 8 and 18 feet.

Installation and Long-Term Use

The fixture mounts directly to flat exterior walls using standard anchors or junction boxes. All wiring is completed from the rear. The adjustable wattage and color temperature allow for on-site tuning during commissioning or future changes.

Routine maintenance is limited to periodic cleaning of the lens and inspection of seals. The integrated photocell reduces manual intervention for daily operation. No relamping or driver replacement is required during the rated life.

How This Fixture Is Commonly Used

Typical mounting heights are 8 to 18 feet, depending on output setting and site requirements. Fixtures are spaced to provide overlapping coverage along building perimeters, entries, and service areas. Spacing varies based on wattage and desired light levels, with higher output settings allowing for wider spacing but potentially increasing glare near entries.

Common deployment includes continuous runs along exterior walls, targeted placement at entry points, and coverage of loading or service areas. The semi cutoff design directs light outward and downward, minimizing uplight and spill.

Safety, Certifications, and Warranty

This fixture is UL listed and IP65 rated. It includes 4kV surge protection and is suitable for wet locations. The product is eligible for utility rebates where applicable.

A 5-year warranty covers manufacturing defects and performance. All components are rated for commercial exterior use.

Frequently Asked Questions

Q: What is the recommended mounting height for this wall pack?

A: Recommended mounting height is 8 to 18 feet, depending on wattage setting and site requirements.

Q: Can the color temperature and wattage be changed after installation?

A: Yes, both color temperature and wattage are field adjustable using onboard switches.

Q: Is this fixture compatible with dimming controls?

A: No, this fixture does not support dimming or networked controls.

Q: Does the integrated photocell require additional wiring?

A: No, the photocell is built in and operates automatically with standard line voltage wiring.

Q: How should fixtures be spaced for perimeter lighting?

A: Spacing depends on wattage and target light levels; higher output allows wider spacing, but glare should be considered near entries and walkways.

Application Questions and Clarification

Q: Is this wall pack suitable for use in loading area lighting?

A: Yes, this fixture is commonly used for loading area lighting on building exteriors.

Q: Can this fixture be used for multifamily exterior lighting?

A: Yes, it is suitable for multifamily exterior wall applications where vandal resistance and reliable operation are required.

Q: Is this fixture appropriate for alley lighting?

A: Yes, it can be used for alley lighting when mounted on exterior walls at appropriate heights.

Q: Can this wall pack be installed on canopy ceilings or poles?

A: No, this fixture is designed for direct wall mounting only and is not intended for canopy or pole installation.