24 Watt Semi Cutoff LED Wall Pack | 3120 Lumens | 5000K | 100-277V

Product Overview

We offer the 24 Watt Semi Cutoff LED Wall Pack for exterior wall-mounted lighting where moderate output and controlled forward throw are required. This fixture is designed for security, perimeter, and entry lighting on commercial and industrial buildings. Typical mounting heights range from 8 to 12 feet, making it suitable for doorways, walkways, and building facades where 100W metal halide fixtures have been used previously.

The semi cutoff design provides forward-aimed illumination while minimizing uplight and glare. The fixture is built for outdoor use, with a die-cast aluminum housing and polycarbonate lens for impact resistance and durability in exposed locations.

Core Performance and Output

This wall pack delivers 3120 lumens at 24 watts, achieving 130 lumens per watt. The 5000K color temperature provides a neutral white output suitable for exterior visibility and security. The 120x90° beam distribution offers broad coverage along building perimeters and entry points without excessive spill light.

Performance is optimized for mounting heights up to 12 feet. At lower heights, output may be excessive for small entryways or residential-scale applications. At higher mounting heights, uniformity and ground-level light levels will decrease.

Adjustability and Control Options

This fixture operates on 100-277V input and is non-dimmable. There are no integrated motion sensors or photocells included. The beam pattern is fixed by the semi cutoff housing and lens design, providing consistent forward and downward distribution.

Control integration can be achieved through external switching or building automation systems if required. No field-adjustable optics or output settings are present.

Longevity and Reliability

The fixture is rated for 50,000 hours (L70), supporting long-term operation with minimal maintenance. The LED driver and board are thermally managed within the die-cast housing to ensure consistent performance over time.

Operating temperature range is -40°F to 113°F. The IP65 rating protects against dust and water ingress, supporting reliable use in exposed exterior environments.

Build Quality and Physical Characteristics

The housing is die-cast aluminum with a bronze finish. The lens is polycarbonate for impact resistance and vandal resistance. The fixture measures 7.72 x 5.83 x 6.54 inches and weighs 3.5 lbs, allowing for direct wall mounting without additional structural support in most cases.

All hardware is corrosion-resistant. The fixture is designed for surface mounting to standard exterior wall construction. No additional brackets or accessories are required for standard installation.

Where This Product Fits Best

This wall pack is suited for exterior wall lighting on commercial and industrial buildings where moderate output and vandal resistance are required. It is commonly used for perimeter security, building entrances, and service areas.

• security lighting
• building facade lighting
• building exterior lighting
• commercial exterior wall lighting
• perimeter lighting
• entry lighting
• service area lighting
• alley lighting

Environments include warehouses, retail buildings, multifamily properties, and service facilities. The fixture is suitable for wet locations and areas exposed to weather, dust, or occasional impact.

Installation and Long-Term Use

Wall mounting is direct to exterior surfaces using standard fasteners. The fixture accepts 100-277V input and is compatible with existing branch circuits. The compact size allows installation above doors, along walkways, or on building corners without interfering with egress or signage.

Routine maintenance is limited to occasional cleaning of the lens and inspection of seals. No relamping is required. The fixture is designed for long-term operation with minimal service requirements.

How This Fixture Is Commonly Used

Typical mounting heights are 8 to 12 feet, spaced 15 to 25 feet apart along building perimeters or above entry points. Spacing and layout depend on required light levels and site geometry. The semi cutoff design directs light forward and downward, reducing glare for pedestrians and minimizing uplight.

Higher output allows for wider spacing, but may increase brightness near entry doors if mounted too low. For uniform coverage, coordinate mounting height and spacing with site-specific requirements.

Safety, Certifications, and Warranty

This fixture is ETL certified and IP65 rated. It meets requirements for wet location exterior use. The housing and lens are designed for vandal resistance and impact protection.

Warranty is 5 years from date of installation. The fixture is rebate eligible where applicable.

Frequently Asked Questions

Q: What is the recommended mounting height for this wall pack?

A: Recommended mounting height is 8 to 12 feet for optimal ground-level illumination and uniformity.

Q: Can this fixture be used in wet or exposed outdoor locations?

A: Yes, the fixture is IP65 rated for wet location use and is suitable for exposed exterior walls.

Q: Is this wall pack dimmable or compatible with motion sensors?

A: This fixture is non-dimmable and does not include integrated motion sensors. External controls can be used if required.

Q: What type of lens is used and is it vandal resistant?

A: The fixture uses a polycarbonate lens designed for impact and vandal resistance.

Q: How does the output compare to a 100W metal halide wall pack?

A: This fixture provides equivalent or higher light output than a typical 100W metal halide wall pack, with improved efficiency and lower maintenance.

Q: How should I plan fixture spacing for perimeter lighting?

A: For perimeter lighting, typical spacing is 15 to 25 feet between fixtures, depending on mounting height and required light levels.

Application Questions and Clarification

Q: Is this fixture suitable for multifamily exterior lighting?

A: Yes, it is commonly used for multifamily exterior wall and entry lighting where moderate output and vandal resistance are needed.

Q: Can this wall pack be used for loading area or service area lighting?

A: Yes, it is suitable for loading area and service area lighting on commercial and industrial buildings.

Q: Is this fixture appropriate for alley lighting behind commercial buildings?

A: Yes, the semi cutoff design and moderate output make it suitable for alley lighting where controlled forward illumination is required.

Q: Does the fixture support installation on non-masonry surfaces?

A: The fixture can be mounted to most exterior wall types, including non-masonry surfaces, using appropriate fasteners and anchors.