150 Watt LED Wall Pack | 19500 Lumens | 5000K | 100-277V | Built-In Photocell

Product Overview

This 150 Watt LED Wall Pack is designed for exterior wall mounting on commercial and industrial buildings. It delivers 19,500 lumens at 5000K, providing high-output illumination for perimeter and security applications. The fixture includes a built-in photocell for dusk-to-dawn operation and is suitable for direct replacement of 400W metal halide wall packs.

Commonly installed on building exteriors, loading areas, and service entrances, this wall pack is built for environments requiring reliable, high-output lighting. The die-cast aluminum housing and polycarbonate lens provide durability for outdoor use in a range of climates.

Core Performance and Output

This fixture outputs 19,500 lumens at 150 watts, achieving 130 lumens per watt. The 120° beam angle provides wide coverage for wall-mounted exterior lighting. Color temperature is 5000K with a CRI above 70, supporting clear visibility and accurate color rendering in outdoor environments.

Power factor exceeds 0.90 and THD is below 20%, supporting stable electrical performance on 100-277V circuits. At lower mounting heights, output may be excessive for small entryways or narrow corridors. Uniformity can decrease if spacing exceeds typical wall pack intervals on large building facades.

Adjustability and Control Options

This wall pack includes a built-in photocell for automatic dusk-to-dawn operation. 1-10V dimming is supported for integration with compatible controls, allowing for output adjustment where required. The fixture is not field-adjustable for beam angle or color temperature.

Photocell operation can be overridden if manual or time-based control is preferred. No motion sensor is included as standard.

Longevity and Reliability

Rated for 50,000 hours of operation, this fixture is designed for long-term exterior use with minimal maintenance. The die-cast aluminum housing and polycarbonate lens resist impact and weathering.

IP65 rating protects against dust and water ingress, supporting reliable performance in rain, snow, and washdown conditions. Operating temperature range is -40°F to 122°F, suitable for most North American climates.

Build Quality and Physical Characteristics

The fixture measures 18.3 x 9.3 x 9 inches and weighs 10 lbs. The housing is bronze-finished die-cast aluminum with a polycarbonate lens for impact resistance and UV stability. All hardware is designed for exterior wall mounting.

Sealed construction and gasketed lens prevent water intrusion. The fixture is ETL listed and meets rebate eligibility requirements. All wiring and mounting points are accessible for standard wall pack installation.

Where This Product Fits Best

This wall pack is intended for exterior wall mounting on commercial and industrial buildings where high-output, wide-distribution lighting is required. It is suitable for use in environments exposed to weather, dust, and temperature extremes.

• security lighting
• building facade lighting
• building exterior lighting
• commercial exterior wall lighting
• perimeter lighting
• entry lighting
• service area lighting
• loading area lighting

IP65 rating and robust construction support use in exposed outdoor locations, including service entrances, loading docks, and multifamily exterior walls.

Installation and Long-Term Use

This fixture is designed for direct wall mounting using standard hardware. All wiring is accessible from the rear compartment. The built-in photocell simplifies dusk-to-dawn operation without additional controls.

Routine maintenance is limited to periodic cleaning of the lens and inspection of seals. The fixture is compatible with 100-277V circuits and supports 1-10V dimming if required. No special tools are needed for installation or servicing.

How This Fixture Is Commonly Used

Typical mounting height ranges from 8 to 20 feet, depending on the area to be illuminated and required light levels. Fixtures are spaced along building exteriors to provide continuous coverage for walkways, entrances, and loading areas.

Higher output allows for wider spacing, reducing fixture count on long facades. In some cases, high lumen output may require careful placement to avoid glare near entry doors or windows.

Safety, Certifications, and Warranty

This fixture is ETL listed and IP65 rated. It is eligible for utility rebates where applicable. The product includes a 5-year warranty covering manufacturing defects and performance.

All components are rated for outdoor use and meet applicable safety standards for exterior lighting installations.

Frequently Asked Questions

Q: What is the recommended mounting height for this 150W wall pack?

A: Typical mounting height is 8 to 20 feet, depending on the area and required coverage.

Q: Can the built-in photocell be bypassed or disabled?

A: Yes, the photocell can be bypassed during installation if manual or alternate control is preferred.

Q: Is this fixture suitable for use in wet locations?

A: Yes, the fixture is IP65 rated for wet location use.

Q: What is the expected lifespan of this wall pack?

A: The rated lifespan is 50,000 hours under normal operating conditions.

Q: How should fixtures be spaced along a building facade?

A: Spacing depends on mounting height and required light levels; higher output allows for wider spacing, but uniformity should be verified for each project.

Application Questions and Clarification

Q: Is this wall pack appropriate for lighting large loading areas?

A: Yes, the 19,500 lumen output supports use in large loading and service areas when mounted at appropriate heights.

Q: Can this fixture be used for multifamily exterior lighting?

A: Yes, it is suitable for multifamily exterior walls, but output may be excessive for small entryways or residential-scale walkways.

Q: Does this fixture support dimming controls?

A: Yes, 1-10V dimming is supported for integration with compatible control systems.

Q: What type of lens material is used?

A: The fixture uses a polycarbonate lens for impact resistance and UV stability.