100 Watt Round Explosion Proof LED Light | 14000 Lumens | Class 1 Div 1 | 5000K | 100-277V or 277-480V

Product Overview

This 100 Watt Round Explosion Proof LED Light is designed for hazardous location lighting where flammable gases, vapors, or combustible dusts are present. It delivers 14,000 lumens at 5000K, providing a high-output solution for environments requiring strict safety compliance. Typical installations include paint booths, chemical processing areas, and Class I Division 1 or Division 2 classified spaces.

The fixture is suitable for mounting heights in the 12 to 25 foot range, replacing legacy 250W metal halide units. It is built for use in environments where both explosive gas and dust hazards exist, and where wet, marine, or corrosive conditions are common.

Core Performance and Output

This fixture outputs 14,000 lumens at 100 watts, achieving 140 lumens per watt. The 120° beam angle provides wide, even coverage for open hazardous areas and booth interiors. Color temperature is 5000K with a CRI above 70, supporting accurate visual inspection and task work.

Electrical performance includes a power factor above 0.95 and THD below 10%. The fixture is available in both 100-277V and 277-480V versions, supporting a range of industrial power systems. Excessive output may occur at mounting heights below 12 feet, and uniformity can decrease if spacing exceeds typical hazardous area layout standards.

Adjustability and Control Options

The fixture supports 1-10V dimming for output adjustment and integration with hazardous location dimming controls. Standard mounting options include yoke and 3/4 inch NPT pendant, allowing for ceiling, wall, or pendant installations based on site requirements.

No field-adjustable optics are provided; the 120° distribution is fixed. Dimming performance is stable across the full voltage range. Controls must be rated for hazardous locations to maintain compliance.

Longevity and Reliability

L70 rated life is 50,000 hours, supporting long-term operation in demanding environments. The fixture is constructed with copper-free aluminum housing and a tempered glass lens, minimizing corrosion and impact risk.

Surge protection is rated at 10kV. The fixture operates reliably from -22°F to 122°F. Maintenance intervals are reduced compared to HID systems, but periodic inspection is required in high-dust or corrosive settings.

Build Quality and Physical Characteristics

The housing is copper-free aluminum with a gray finish, designed for marine and chemical resistance. The fixture is IP66 and IK10 rated, supporting use in wet, dusty, and high-impact areas. Weight is 39 lbs, and dimensions are 16 x 13.5 inches.

UL 844, UL 1598, UL 1598A, ATEX, and IECEx certifications are met. The tempered glass lens is sealed for ingress protection. All hardware is designed for hazardous and marine environments.

Where This Product Fits Best

This fixture is intended for hazardous locations where explosive gases, vapors, or dusts are present, and where wet or corrosive conditions may exist. It is commonly installed in:

• hazardous location lighting
• explosion proof lighting
• paint booth lighting
• chemical processing facility lighting
• oil and gas facility lighting
• refinery lighting
• marine environment lighting
• wastewater treatment lighting

Environmental characteristics include high resistance to water, dust, impact, and corrosive agents. The fixture is suitable for both indoor and outdoor hazardous classified areas, including marine and offshore locations.

Installation and Long-Term Use

Mounting options include yoke and 3/4 inch NPT pendant, supporting ceiling, wall, or pendant installations. The fixture?s weight and size require secure mounting to rated structures. All wiring and connections must comply with hazardous location codes and standards.

Routine inspection is recommended in environments with heavy dust, chemical exposure, or vibration. The fixture?s sealed design reduces maintenance frequency, but lens cleaning and hardware checks should be included in scheduled maintenance cycles.

How This Fixture Is Commonly Used

Typical mounting heights range from 12 to 25 feet, depending on area size and required light levels. Fixtures are spaced to achieve uniform coverage and meet hazardous area lighting standards, often following grid or linear patterns in process areas and booths.

Higher output allows for wider spacing, but glare may increase if fixtures are mounted too low or used in confined spaces. Layouts are determined by hazard classification, area geometry, and required illumination levels.

Safety, Certifications, and Warranty

This fixture is certified to UL 844, UL 1598, UL 1598A, ATEX, IECEx, and ABS standards. It meets Class I Division 1 and 2, Class II Division 1 and 2, and Class III requirements. IP66 and IK10 ratings are provided for ingress and impact protection.

Operating temperature range is -22°F to 122°F. The fixture includes a 5-year warranty. All certifications and ratings are maintained when installed per manufacturer instructions and hazardous location codes.

Frequently Asked Questions

Q: What hazardous location classifications does this fixture meet?

A: This fixture is certified for Class I Division 1 and 2, Class II Division 1 and 2, and Class III hazardous locations.

Q: What mounting options are available?

A: Standard mounting options are yoke and 3/4 inch NPT pendant.

Q: What is the recommended mounting height for this fixture?

A: Typical mounting heights are 12 to 25 feet, depending on area size and required light levels.

Q: Can this fixture be used in marine or offshore environments?

A: Yes, it is UL 1598A Marine Outside Type and ABS certified for marine and offshore use.

Q: How should fixture spacing be determined in hazardous areas?

A: Spacing depends on area geometry, hazard classification, and required illumination. Wider spacing is possible at higher mounting heights, but uniformity and code requirements must be maintained.

Application Questions and Clarification

Q: Is this fixture suitable for use in paint booths with flammable vapors?

A: Yes, it is certified for use in paint booths and classified hazardous locations with flammable vapors.

Q: Can this fixture be installed in chemical processing areas with corrosive atmospheres?

A: Yes, the copper-free aluminum housing and sealed design support use in chemical processing and corrosive environments.

Q: Is this fixture appropriate for wastewater treatment facilities with combustible dust hazards?

A: Yes, it meets Class II and III hazardous location requirements for dust and fiber hazards in wastewater treatment environments.

Q: Does this fixture support dimming in hazardous locations?

A: Yes, it supports 1-10V dimming when used with hazardous location-rated controls.