80 Watt Round High Temperature Explosion Proof LED Light | 8000 Lumens | Class 1 Div 2 | 5000K | 120V | Rated to 194F

Product Overview

This 80 Watt Round High Temperature Explosion Proof LED Light is engineered for hazardous location lighting in environments with elevated ambient temperatures. The fixture is rated for continuous operation up to 194°F (90°C) and delivers 8000 lumens at 5000K. It is designed for use in classified areas requiring Class I Division 2, Class II Division 1 and 2, and Class III compliance, with a robust build for industrial furnace areas, steel mills, and similar high-heat, hazardous settings.

Typical installations include replacement of 250W metal halide fixtures in high temperature zones where explosive gases, dusts, or fibers may be present. The fixture supports yoke or 3/4 inch NPT pendant mounting, allowing for flexible installation in both new and retrofit projects.

Core Performance and Output

This fixture outputs 8000 lumens at 100 lumens per watt, providing targeted illumination for hazardous, high temperature environments. The 120° beam angle supports broad, uniform coverage in open industrial spaces. The fixture operates at 120V with a power factor above 0.95 and total harmonic distortion below 10%.

Performance is stable across the full rated temperature range, but excessive output may occur at mounting heights below 10 feet. At higher mounting heights, uniformity may decrease if spacing exceeds typical patterns for this output class.

Adjustability and Control Options

This model does not include dimming or advanced control features. The fixture is designed for continuous, full-output operation in hazardous and high temperature environments. The yoke mount allows for aiming adjustment during installation, while the pendant mount provides fixed vertical orientation.

No integrated motion sensors or networked controls are available for this unit. Control must be managed at the circuit or panel level.

Longevity and Reliability

The fixture is rated for 50,000 hours (L70) at maximum ambient temperature. The copper-free aluminum housing, tempered glass lens, and IP66/IK10 ratings support long-term operation in harsh, dusty, and wet conditions. Surge protection is rated at 10kV.

Reliability is maintained in continuous high temperature operation, with no reduction in rated life at 194°F. Maintenance requirements are minimal due to the sealed design and lack of moving parts.

Build Quality and Physical Characteristics

The fixture housing is constructed from copper-free aluminum with a gray finish. The tempered glass lens provides impact resistance and chemical durability. The fixture measures 9.1 x 8.7 inches and weighs 15 lbs, supporting both yoke and pendant mounting methods.

Ingress protection is IP66, and impact protection is IK10. The fixture is certified for marine outside type (UL 1598A) and ABS, supporting use in corrosive and offshore environments. Operating temperature range is -40°F to 194°F.

Where This Product Fits Best

This fixture is intended for hazardous locations and high temperature industrial environments where explosive gases, dusts, or fibers may be present. It is suitable for continuous operation in areas with ambient temperatures up to 194°F, including steel mills, foundries, and power generation facilities.

• high temperature facility lighting
• hazardous location lighting
• explosion proof lighting
• industrial furnace area lighting
• steel mill lighting
• paint booth lighting
• chemical processing facility lighting
• oil and gas facility lighting

The fixture is designed for environments with high ambient heat, airborne contaminants, and classified hazardous conditions. It is not suitable for low temperature or general-purpose industrial spaces.

Installation and Long-Term Use

The fixture supports yoke and 3/4 inch NPT pendant mounting for ceiling, wall, or structure attachment. Typical mounting heights range from 10 to 20 feet, depending on required light levels and area coverage. The compact form factor allows installation in confined or obstructed spaces.

Wiring is completed through sealed conduit entries to maintain hazardous location compliance. Routine inspection of seals and mounting hardware is recommended in high vibration or corrosive environments. No relamping or lens cleaning is required under normal conditions.

How This Fixture Is Commonly Used

Commonly installed in high temperature hazardous areas such as furnace decks, steel mill production lines, and chemical process zones. Fixtures are spaced to achieve uniform coverage, typically 1.0 to 1.5 mounting heights apart, depending on reflectance and obstructions.

Mounting heights of 12 to 18 feet are standard for this output class. Higher output per fixture can reduce total fixture count, but may increase glare in areas with low ceilings or reflective surfaces.

Safety, Certifications, and Warranty

This fixture is certified to UL 844, UL 1598, UL 1598A, and ABS standards. It meets Class I Division 2, Class II Division 1 and 2, and Class III hazardous location requirements. The fixture is IP66 and IK10 rated for ingress and impact protection.

Operating temperature is rated to 194°F. The product includes a 5-year warranty covering manufacturing defects and performance within rated conditions.

Frequently Asked Questions

Q: What is the maximum ambient temperature for continuous operation?

A: The fixture is rated for continuous operation at ambient temperatures up to 194°F (90°C).

Q: Which hazardous location classifications does this fixture meet?

A: The fixture is certified for Class I Division 2, Class II Division 1 and 2, and Class III hazardous locations.

Q: What mounting options are available?

A: The fixture supports yoke mounting and 3/4 inch NPT pendant mounting.

Q: Is this fixture dimmable or compatible with motion sensors?

A: No, this fixture does not support dimming or integrated motion sensors.

Q: What is the recommended spacing for uniform coverage?

A: Typical spacing is 1.0 to 1.5 times the mounting height, depending on area reflectance and obstructions.

Application Questions and Clarification

Q: Can this fixture be used in a steel mill furnace area with high airborne dust?

A: Yes, the fixture is designed for high temperature and hazardous locations with airborne dust, meeting IP66 and relevant hazardous location certifications.

Q: Is this fixture suitable for paint booth lighting in classified areas?

A: Yes, the fixture is certified for use in paint booths requiring explosion proof and high temperature rated lighting.

Q: Can this fixture be installed in a marine or offshore hazardous environment?

A: Yes, the fixture is UL 1598A Marine Outside Type and ABS certified for marine and offshore hazardous locations.

Q: Is this fixture appropriate for general warehouse or gymnasium lighting?

A: No, this fixture is intended for hazardous and high temperature environments, not for general-purpose warehouse or gymnasium lighting.