100 Watt LED High Temperature Light | 15000 Lumens | 5000K | 100-277V | Rated to 302F

Product Overview

This 100 watt LED high temperature fixture delivers 15,000 lumens at 5000K and operates in ambient temperatures from -40°F to 302°F. The fixture uses an external driver connected by a standard 5-meter (15 ft) cord, with the option to mount the driver up to 68 feet from the fixture head. The driver itself must be installed where ambient temperature does not exceed 212°F.

The aluminum alloy housing incorporates a large heat sink designed for sustained operation in extreme thermal environments. At 150 lumens per watt, this fixture replaces 400 watt metal halide systems. Voltage input accepts 100V-277V at 50/60 Hz.

Mounting options include eye-hook, pendant, or yoke configurations. The fixture measures 14 x 12 x 4 inches and weighs 16 lbs. A tempered glass lens protects the LED array, and the 120-degree beam angle provides broad light distribution.

Where This Product Fits Best

This fixture is built for locations where standard LED high bays cannot survive. Foundries, glass manufacturing plants, heat treatment facilities, steel mills, and industrial ovens present ambient conditions that destroy conventional fixtures. The 302°F maximum operating temperature allows installation in areas with radiant heat exposure or elevated process temperatures.

The external driver design addresses a common failure point in high-heat applications. By separating the driver from the fixture head and allowing up to 68 feet of separation, the electronics can be positioned in a cooler zone while the light head remains in the heat. This is critical in applications where ceiling temperatures exceed what integrated-driver fixtures can tolerate.

The -40°F low-end rating also makes this fixture suitable for cold storage, blast freezers, and unheated industrial buildings in extreme climates. IP66 protection allows use in washdown areas and environments with dust, steam, or moisture exposure.

Performance and Functional Considerations

Output is fixed at 15,000 lumens with no dimming capability. This is a single-output fixture intended for applications where consistent light levels are required and dimming controls are not part of the lighting plan. CRI is rated at 75+, which is typical for industrial task lighting but not suited for color-critical inspection or quality control areas.

The 6kV surge protection rating provides a level of defense against electrical transients common in industrial facilities with heavy motor loads, welding equipment, or variable frequency drives. Power factor exceeds 0.95 and THD is under 15%, which supports stable operation on facility electrical systems without introducing significant harmonic distortion.

Rated lifespan is 100,000 hours at L70, meaning the fixture is expected to retain at least 70% of initial output at that point. In high-temperature environments, actual lifespan will depend on how consistently the driver is kept within its 212°F maximum limit.

Installation and Long-Term Use

The fixture ships with a 5-meter cord connecting the light head to the external driver. For installations requiring greater separation, the driver can be mounted up to 68 feet away from the fixture. The driver location must not exceed 212°F ambient?this is a hard constraint that affects placement decisions in heat-intensive environments.

Mounting hardware supports eye-hook, pendant, or yoke installation. The 16 lb fixture weight and 14 x 12 x 4 inch dimensions should be factored into structural support and clearance planning. The aluminum alloy housing and tempered glass lens are designed to withstand thermal cycling and physical stress in demanding industrial settings.

IP66 protection means the fixture is sealed against dust ingress and protected against high-pressure water jets, supporting use in environments where regular cleaning or incidental water exposure occurs.

How This Fixture Is Commonly Used

Facilities with process heat or radiant exposure from equipment typically install this fixture where the light head is in direct line with elevated temperatures but the driver is routed to a protected location?above a dropped ceiling, inside a conditioned electrical room, or along a cooler wall run. The 68-foot maximum cord distance gives flexibility in routing the driver away from heat sources.

Because this fixture does not dim, it is used in spaces where full output is always required or where lighting control is handled at the circuit or zone level rather than per fixture. The 120-degree beam angle and 15,000 lumen output support general area lighting over work zones, aisles, or equipment areas.

In cold storage applications, the same thermal resilience works in reverse?standard fixtures may fail or produce reduced output at low temperatures, while this unit operates normally down to -40°F.

Safety, Certifications, and Warranty

This fixture is ETL listed. It is backed by a 5-year warranty from LED Lighting Supply.

IP66 rating allows installation in wet or dusty environments. The 6kV surge protection supports use in electrically noisy industrial facilities.

Frequently Asked Questions

What voltage does this fixture accept?
The fixture operates on 100V-277V input at 50/60 Hz.

Can this fixture be dimmed?
No. This is a fixed-output fixture with no dimming capability.

What is the maximum operating temperature?
The fixture head operates in ambient temperatures up to 302°F. The external driver must be installed where ambient temperature does not exceed 212°F.

How far can the driver be mounted from the fixture?
The driver can be mounted up to 68 feet from the fixture head. A 5-meter (15 ft) cord is included.

What mounting options are available?
Eye-hook, pendant, and yoke mounting options are supported.

Is this fixture rated for wet or dusty environments?
Yes. IP66 protection allows use in locations with dust exposure and direct water spray.

What is the warranty?
This fixture carries a 5-year warranty.

Application Questions and Clarification

This product description reflects the provided specifications, ratings, and configuration options. For questions related to site-specific conditions, electrical compatibility, control integration, or application requirements not addressed in the provided data, our team is available to provide clarification.