35 Foot Fiberglass Flag Pole | 7 Inch Base Diameter | External Halyard | Anchor Base | Rated for 125 MPH

Product Overview

This 35 Foot Fiberglass Flag Pole is designed for permanent flag display at commercial, municipal, and institutional sites. The pole features a 7 inch base diameter and is constructed from non-conductive, corrosion-resistant fiberglass for long-term outdoor use. The external halyard system, stationary truck, and gold ball top are included for standard flag operation. Typical installations include building entrances, facility grounds, and open campus areas where a 35 foot mounting height is appropriate for visibility and scale.

The anchor base design supports secure installation on concrete foundations using a 9-11 inch bolt circle. The pole is finished in white and weighs 97 lbs, supporting a standard 5 x 8 foot flag. Wind rating is 125 mph (unflagged), suitable for most non-coastal and inland environments.

Core Performance and Output

This fiberglass flag pole is engineered for structural stability and environmental durability. The 7 inch base diameter and 10.24 x 10.24 inch anchor base provide a solid foundation for 35 foot installations. The pole is rated for 125 mph wind loads (unflagged), meeting requirements for most commercial and municipal sites outside of hurricane-prone regions.

The fiberglass construction offers high resistance to corrosion, UV exposure, and electrical conductivity. The pole supports a standard 5 x 8 foot flag with an external halyard system. Excessive flag size or installation in areas with frequent high winds may require additional engineering review. Anchor bolts and base cover are not included and must be specified separately.

Adjustability and Control Options

This model uses an external halyard system with a #10 (5/16 inch) rope, nylon cleat, and brass snaps with vinyl covers. The stationary truck and gold ball top are standard. The halyard system allows for manual raising and lowering of the flag from ground level.

No internal halyard, winch, or locking mechanism is included. The pole is not designed for automated or remote flag operation. Adjustments are limited to flag position and halyard tension using the provided cleat and hardware.

Longevity and Reliability

The fiberglass material provides long-term resistance to weathering, corrosion, and UV degradation. The pole is suitable for continuous outdoor exposure and requires minimal maintenance compared to metal alternatives. The white finish is integral to the fiberglass and does not require repainting under normal conditions.

All hardware components are specified for outdoor use. The 15 year warranty covers structural integrity and material performance under standard operating conditions. Routine inspection of halyard, cleat, and snaps is recommended to ensure reliable flag operation.

Build Quality and Physical Characteristics

The pole measures 35 feet in total height with a 7 inch ground-level outside diameter and a 3 inch tip diameter. The anchor base is designed for a 9-11 inch bolt circle with 3/4 inch diameter bolts (sold separately). The pole weighs 97 lbs, supporting manageable handling during installation with proper equipment.

Standard fittings include an 8 inch gold ball top, stationary truck, external halyard hardware, 8.5 inch nylon cleat, and one set of brass snaps with white vinyl covers. The white finish is smooth and uniform. The pole is non-conductive and suitable for locations where electrical isolation is required.

Where This Product Fits Best

This flag pole is intended for permanent outdoor flag display at sites requiring a 35 foot mounting height and moderate wind resistance. The fiberglass construction is appropriate for environments where corrosion or electrical conductivity are concerns. Typical installations include:

• flag display
• commercial property flag mounting
• municipal flag installation
• facility flag display
• school flag installation
• government building flag display
• stadium flag display
• corporate facility flag display

The pole is suitable for open grounds, building entrances, and campus settings. It is not intended for coastal hurricane zones or locations requiring higher wind ratings without engineering review.

Installation and Long-Term Use

Installation requires a concrete foundation with a 9-11 inch bolt circle and 3/4 inch diameter anchor bolts (not included). The anchor base design allows for secure mounting and vertical alignment. The 97 lb pole weight supports safe handling with standard lifting equipment.

Routine maintenance includes inspection of halyard, cleat, and flag hardware. The fiberglass surface can be cleaned with mild detergent and water. No painting or surface treatment is required under normal conditions. Replacement of halyard or hardware may be needed over time depending on site conditions and usage frequency.

How This Fixture Is Commonly Used

This flag pole is typically installed at mounting heights of 35 feet, providing clear flag visibility for commercial, municipal, and institutional properties. Spacing between poles is determined by site layout and flag size, with single or grouped installations common at facility entrances or open grounds.

Standard layout practice is to position the pole for maximum visibility from primary approach routes or gathering areas. Using a larger flag or installing in high-wind areas may require increased attention to halyard tension and hardware wear. Higher mounting height increases visibility but may require additional planning for installation equipment and foundation design.

Safety, Certifications, and Warranty

The pole is non-conductive and corrosion-resistant, supporting safe installation near electrical infrastructure or in chemically aggressive environments. All hardware is specified for outdoor use. Wind rating is 125 mph (unflagged). Warranty is 15 years for structural and material performance.

Anchor bolts and base cover are not included and must be specified to match foundation requirements. Routine inspection of halyard and hardware is recommended to maintain safe flag operation. No additional certifications are specified for this product.

Frequently Asked Questions

Q: What is the maximum flag size recommended for this pole?

A: The standard flag size for this pole is 5 x 8 feet. Larger flags may exceed wind load ratings and are not recommended without engineering review.

Q: What type of foundation is required for installation?

A: A concrete foundation with a 9-11 inch bolt circle and 3/4 inch diameter anchor bolts is required. Anchor bolts and base cover are sold separately.

Q: Can this pole be installed in coastal or hurricane-prone areas?

A: The pole is rated for 125 mph wind loads (unflagged). For coastal or hurricane-prone areas, higher wind ratings may be required. Site-specific engineering review is recommended.

Q: Is the halyard system lockable or internal?

A: This model uses an external halyard system with a nylon cleat. No internal halyard or locking mechanism is included.

Q: How often should the halyard and hardware be inspected?

A: Routine inspection is recommended at least annually, or more frequently in high-wind or high-usage environments.

Q: What is the typical spacing between flag poles at a facility entrance?

A: Spacing varies by site layout and flag size. For grouped installations, 15 to 25 feet between poles is common to prevent flag interference and maintain visual separation.

Application Questions and Clarification

Q: Is this pole suitable for stadium flag display?

A: Yes, this pole is commonly used for stadium flag display where a 35 foot mounting height and 125 mph wind rating are appropriate.

Q: Can this pole be used for government building flag installations?

A: Yes, this model is suitable for government building flag display, provided the wind rating and mounting height meet site requirements.

Q: Is the fiberglass construction appropriate for school flag installations?

A: Yes, the non-conductive and corrosion-resistant fiberglass construction is suitable for school flag installations and similar institutional sites.

Q: Does this pole support multiple flags?

A: The standard configuration supports one flag. Additional hardware may be required for multiple flag display and should be specified separately.