22 / 28 / 36 / 44 Watt Adjustable Shop Light | 4 Foot | 3102 / 3948 / 5076 / 6204 Lumens | 3500K / 4000K / 5000K Adjustable | 100-277V

Product Overview

This is a 4-foot LED shop light with selectable wattage and color temperature, designed for general-purpose task and area lighting in commercial and industrial workspaces. The fixture offers four wattage settings?22, 28, 36, and 44 watts?delivering up to 6204 lumens. It is intended as a direct replacement for fluorescent strip lights in workshops, garages, and maintenance shops, with mounting options for surface or suspension using V-hooks. Typical mounting heights range from 8 to 14 feet, suitable for workbenches, service bays, and small warehouse areas.

The fixture operates on 100-277V and supports 1-10V dimming. Color temperature can be set to 3500K, 4000K, or 5000K to match task requirements or ambient conditions. The housing is galvanized steel with a frosted lens for glare control and uniform light distribution.

Core Performance and Output

This shop light provides selectable output from 3102 to 6204 lumens, with a maximum efficacy of 141 lumens per watt. The 120° beam angle and frosted lens deliver wide, even coverage for bench work, tool rooms, and service bays. Color rendering is 80+ CRI, supporting accurate visual tasks.

Output is adjustable by wattage selection, allowing tuning for the space and mounting height. At lower mounting heights, the highest wattage setting may produce excessive brightness or glare. For ceiling heights above 14 feet, uniformity and light levels may decrease unless fixtures are spaced more closely.

Adjustability and Control Options

Both wattage and color temperature are field-selectable via onboard switches. This allows adjustment during installation or future reconfiguration without replacing the fixture. The fixture supports 1-10V dimming for integration with compatible controls or occupancy sensors.

Color temperature can be set to 3500K, 4000K, or 5000K. Wattage can be set to 22, 28, 36, or 44 watts. No onboard motion sensor is included; external controls must be specified separately if required.

Longevity and Reliability

The fixture is rated for 50,000 hours (L70), supporting long-term operation in commercial and industrial environments. The galvanized steel housing and frosted polycarbonate lens provide durability against routine impacts and handling.

All components are designed for consistent performance across the full voltage range (100-277V, 50/60 Hz). The power factor is greater than 0.90, minimizing electrical losses and supporting stable operation in multi-fixture installations.

Build Quality and Physical Characteristics

The fixture measures 46 7/8 inches long, 2 1/2 inches wide, and 2 11/16 inches high, with a total weight of 4.6 lbs. The housing is galvanized steel, finished in white, and the lens is frosted for glare reduction. No power cord is included; hardwiring is required.

Mounting options include direct surface mounting or suspension using included V-hooks. The fixture is UL listed and meets requirements for rebate eligibility in many regions.

Where This Product Fits Best

This shop light is designed for indoor commercial and industrial environments where task lighting, bench lighting, or general area lighting is required at low to moderate mounting heights. It is commonly used in:

• workshop lighting
• maintenance shop lighting
• garage lighting
• service bay lighting
• small warehouse lighting
• tool room lighting
• automotive shop lighting
• equipment repair lighting

The fixture is suitable for dry or damp locations where routine cleaning and maintenance are required. It is not intended for wet locations or environments with corrosive chemicals.

Installation and Long-Term Use

Installation can be completed by surface mounting directly to the ceiling or suspending with V-hooks and chain. The fixture is designed for hardwired connection to 100-277V circuits. No cord is supplied, and field wiring is required.

Routine maintenance is limited to lens cleaning and periodic inspection. The steel housing and frosted lens resist common impacts and dust accumulation. For long-term reliability, ensure the fixture is not exposed to water spray or corrosive vapors.

How This Fixture Is Commonly Used

Typical mounting heights range from 8 to 14 feet, with fixtures spaced to provide uniform coverage over workbenches, tool areas, or vehicle bays. In garages and workshops, fixtures are often installed in rows above work areas or perimeter walls.

Spacing and layout depend on selected wattage and required light levels. Higher output settings reduce fixture count but may increase glare if installed too close to work surfaces. Adjust wattage and color temperature to match task requirements and user preference.

Safety, Certifications, and Warranty

This fixture is UL listed and meets safety requirements for commercial and industrial lighting. It is eligible for utility rebates where applicable. The product includes a 5-year warranty covering manufacturing defects and component failure under normal use.

No special safety procedures are required beyond standard electrical installation practices. Follow all local codes and guidelines for hardwired connections and mounting.

Frequently Asked Questions

Q: What is the recommended mounting height for this shop light?

A: The fixture is typically installed at heights between 8 and 14 feet for optimal light distribution and visual comfort.

Q: Can the wattage and color temperature be changed after installation?

A: Yes, both wattage and color temperature are field-selectable using onboard switches and can be adjusted as needed.

Q: Is this fixture compatible with occupancy sensors or dimming controls?

A: The fixture supports 1-10V dimming and can be integrated with compatible external controls or sensors.

Q: What is the expected lifespan of the fixture?

A: The rated lifespan is 50,000 hours (L70), based on standard operating conditions.

Q: How should fixtures be spaced for uniform lighting in a workshop?

A: Spacing depends on selected wattage and desired light levels; closer spacing improves uniformity, especially at lower wattage settings.

Application Questions and Clarification

Q: Is this fixture suitable for use in automotive repair shops?

A: Yes, it is commonly installed in automotive shop lighting and equipment repair lighting applications.

Q: Can this shop light be used in small warehouse areas?

A: The fixture is suitable for small warehouse lighting at mounting heights up to 14 feet.

Q: Is this fixture intended for wet or corrosive environments?

A: No, it is not designed for wet locations or areas with corrosive chemicals; use in dry or damp indoor spaces only.

Q: Does the fixture include a power cord for plug-in installation?

A: No, the fixture is designed for hardwired installation and does not include a power cord.