63 / 90 / 108 Watt Adjustable Semi Cutoff LED Wall Pack | 8800 to 14500 Lumens | 3000K / 4000K / 5000K Adjustable | 100-277V | Built-In Photocell

Product Overview

This semi cutoff LED wall pack delivers field-adjustable output from 63 to 108 watts, producing 8,800 to 14,500 lumens depending on the selected wattage setting. The fixture replaces 400 watt metal halide wall packs and operates at 134 lumens per watt across all output levels. A built-in photocell enables automatic dusk-to-dawn operation without additional controls.

Color temperature is adjustable between 3000K, 4000K, and 5000K, allowing the fixture to match site requirements or existing installations. The semi cutoff optical design uses a polycarbonate lens to direct light forward and downward while limiting upward light output. The die-cast aluminum housing is finished in bronze and measures 14.3 x 9.3 x 5.9 inches at 8 pounds.

The fixture accepts 100-277V input at 50-60Hz, with power factor greater than 0.9 and total harmonic distortion under 20 percent. Rated lifespan is 50,000 hours at L70. This wall pack does not dim.

Where This Product Fits Best

This wall pack is sized for building perimeters, loading docks, service entrances, and parking area walls where 400 watt metal halide fixtures are currently installed. The 8,800 to 14,500 lumen output range covers applications from low-activity side entrances to high-traffic loading zones. Semi cutoff distribution suits installations where some light is needed at wider angles but uplight must be controlled.

The IP65 rating allows installation where the fixture will be exposed to rain, snow, and hose-down spray. Operating temperature range of -40 degrees F to 113 degrees F supports year-round use in both cold-climate and high-heat environments. The 4kV surge protection addresses electrical transients common in industrial and commercial electrical systems.

Bronze finish is appropriate for buildings where darker hardware blends with masonry, stucco, or earth-toned facades. The built-in photocell eliminates the need for timers or manual switching in dusk-to-dawn applications.

Performance and Functional Considerations

At 63 watts, the fixture produces 8,800 lumens. At 90 watts, output increases to 12,000 lumens. The 108 watt setting delivers 14,500 lumens. All three settings maintain 134 lumens per watt efficiency. Wattage selection is made at the fixture, allowing output to be matched to actual site conditions.

Color temperature selection between 3000K, 4000K, and 5000K affects the appearance of illuminated surfaces and the overall character of the lit environment. Lower color temperatures produce warmer light suited to retail or hospitality-adjacent areas. Higher color temperatures produce cooler light often preferred in industrial or security applications.

CRI is rated at 70 or higher. This level of color rendering is standard for exterior security and area lighting where color accuracy is secondary to visibility. The polycarbonate lens provides impact resistance appropriate for wall-mounted fixtures at accessible heights.

Installation and Long-Term Use

The fixture mounts directly to a wall surface. Die-cast aluminum construction supports the 8 pound fixture weight and resists corrosion in exterior environments. The IP65 rating means the fixture is sealed against dust ingress and protected against water jets from any direction.

Electrical connection requires 100-277V supply. The built-in photocell requires no wiring beyond standard line voltage. Wattage and color temperature adjustments are made at the fixture during installation or when conditions change. The fixture does not require dimming infrastructure.

Rated lifespan of 50,000 hours at L70 means the fixture is expected to retain at least 70 percent of initial lumen output at that point. The 5 year warranty covers the fixture under normal operating conditions.

How This Fixture Is Commonly Used

The adjustable wattage allows installers to set output based on observed conditions rather than pre-calculated assumptions. A fixture mounted at a secondary entrance may be set to 63 watts, while the same fixture at a primary loading dock can run at 108 watts. This flexibility addresses variations in mounting height, surface reflectance, and required light levels across different wall locations on the same building.

The color temperature switch gives facility operators the ability to match the fixture to adjacent lighting or to meet tenant preferences. Buildings with multiple wall pack locations can maintain visual consistency by setting all fixtures to the same color temperature.

The built-in photocell handles on-off control automatically. The fixture turns on at dusk and off at dawn without timers, switches, or external sensors. This is the primary control method for most perimeter wall pack applications.

Safety, Certifications, and Warranty

This fixture is UL listed. It is rebate eligible through applicable utility programs. The 4kV surge protection rating addresses transient voltage events from grid fluctuations, nearby equipment cycling, or lightning-induced surges.

IP65 rating confirms the fixture is dust-tight and protected against water jets. Operating temperature range spans -40 degrees F to 113 degrees F, covering extreme cold and high ambient heat conditions.

We provide a 5 year warranty on this fixture.

Frequently Asked Questions

What voltage does this wall pack require?
The fixture operates on 100-277V input at 50-60Hz.

What does this fixture replace?
It replaces 400 watt metal halide wall packs.

Is this fixture rebate eligible?
Yes, this fixture is rebate eligible through participating utility programs.

Can I adjust the wattage and color temperature after installation?
Yes, both wattage and color temperature are field adjustable at the fixture.

Does this fixture include a photocell?
Yes, the photocell is built in for automatic dusk-to-dawn operation.

Is this fixture suitable for wet locations?
The IP65 rating allows use in locations exposed to rain, snow, and direct water spray.

What is the warranty period?
This fixture carries a 5 year warranty.

Application Questions and Clarification

This product description reflects the provided specifications, ratings, and configuration options. For questions related to site-specific conditions, electrical compatibility, control integration, or application requirements not addressed in the provided data, our team is available to provide clarification.